EasyManua.ls Logo

Watson Marlow Pumps 500 Series - User Manual

Watson Marlow Pumps 500 Series
128 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
530 U/UN Installation, operating, and maintenance manual
m-530un-en-08 1
Contents
1 Declaration of conformity 5
2 Declaration of incorporation 6
3 When you unpack your pump 7
3.1 Unpacking your pump 7
3.2 Packaging disposal 7
3.3 Inspection 7
3.4 Components supplied 7
3.5 Storage 7
4 Information for returning pumps 8
5 Peristaltic pumps - an overview 8
6 Warranty 9
7 Safety notes 10
8 Pump specifications 13
8.1 Specification ratings 13
8.2 Weights 13
8.3 Pumphead options 14
9 Good pump installation practice 15
9.1 General recommendations 15
9.2 Dos and don'ts 16
10 Pump operation 17
10.1 Keypad Layout and Key IDs 17
10.2 Starting and stopping 18
10.3 Using up and down keys 18
10.4 Maximum speed 18
10.5 Change rotation direction 18
11 Connecting to a power supply 19
11.1 Conductor colour coding 20

Table of Contents

Other manuals for Watson Marlow Pumps 500 Series

Preview: User Manual
User Manual19 pages

Questions and Answers

  • J
    Julie BlackJul 26, 2025
    What to do if my Watson Marlow Pumps Water Pump runs but has little or no flow?
    • M
      Mary CunninghamJul 26, 2025
      If your Watson Marlow Pumps Water Pump runs but has little or no flow, here are some things to check: * Make sure fluid is being supplied to the pump. * Inspect the lines for kinks or blockages. * Ensure any valves in the line are open. * Verify the tube and rotor are correctly placed in the pumphead. * Check the tube for splits or bursts. * Confirm the correct wall-thickness tube is being used. * Check the direction of rotation. * Make sure the rotor isn't slipping on the drive shaft.
  • P
    pspencerAug 2, 2025
    How to fix a blank display on Watson Marlow Pumps 500 Water Pump?
    • J
      Jeremiah LiAug 2, 2025
      If the display on your Watson Marlow Pumps Water Pump is blank when you switch it on, try the following: * Ensure the pump is receiving mains power. * Check the fuse in the wall plug, if there is one. * Verify the position of the voltage selector switch. * Check the mains power switch located at the rear of the pump. * Inspect the fuse in the fuse holder on the switch plate at the rear of the pump.
  • J
    jacob07Aug 9, 2025
    What to do if Watson Marlow Pumps 500 Water Pump shows a red error screen?
    • D
      Deborah McguireAug 9, 2025
      If your Watson Marlow Pumps Water Pump displays an internal error screen with a red background: * Immediately stop the pump. Inspect the pumphead and tube. * Check the power supply. * Check the analog control signal range and trim if needed. * Reduce the analog control signal. Powering the pump off and on may reset the system. If problems persist, seek support.
  • S
    sonya64Aug 17, 2025
    How to troubleshoot PROFIBUS control issues with Watson Marlow Pumps 500 Water Pump?
    • E
      Eric TaylorAug 17, 2025
      If your Watson Marlow Pumps Water Pump is not controllable under PROFIBUS, check the following: * Confirm that PROFIBUS wiring has been correctly installed. * Ensure the pump's PROFIBUS address is set and PROFIBUS is enabled. * Verify the pump has been switched to PROFIBUS control using the MODE menu or key. * Check that the pump is not displaying an error message. * Ensure the PROFIBUS master hasn't diagnosed a problem with the pump or its connection.

Summary

Warranty

Safety notes

Pump specifications

Good pump installation practice

9.1 General recommendations

Guidance on siting, ventilation, and environmental conditions for pump installation.

9.2 Dos and donts

Lists recommended practices and common mistakes for pump installation.

Pump operation

10.1 Keypad Layout and Key IDs

Identifies and explains the function of each key on the pump's keypad.

Connecting to a power supply

Start-up check list

Control wiring

Standard N - Module

SCADA N-Module

Switching the pump on for the first time

14.1 Selecting the display language

Guide to selecting the preferred language for the pump display.

First-time start-up defaults

Switching the pump on in subsequent power cycles

Mode menu

Manual

Flow calibration

18.1 Setting the flow calibration

Steps to set up and perform flow calibration on the pump.

Analog mode

19.1 Analog calibration

Procedure for calibrating analog input signals for remote control.

MemoDose mode

Main menu

21.1 Security settings

Configuration options for keypad lock and PIN protection.

General settings

Control settings

Configure outputs

Configure inputs

Troubleshooting

22.1 Leak detection

Information on detecting and responding to leaks.

22.2 Error codes

List of error codes, their conditions, and suggested actions.

Pumphead replacement

Tube replacement

26.1 Continuous tubing

26.2 Tube elements

Watson Marlow Pumps 500 Series Specifications

General IconGeneral
TypePeristaltic Pump
Motor TypeBrushless DC
Control OptionsManual, Remote
Operating Temperature40°C
Power Supply24VDC

Related product manuals