What does error Er15 mean on Watson Marlow Pumps Water Pump?
If the display of your Watson Marlow Pumps Water Pump shows error code Er15 (Over current), immediately stop the pump. A power cycle (OFF/ON) may reset the system.
What does error Er21 mean on Watson Marlow Pumps 630?
If your Watson Marlow Pumps Water Pump displays error code Er21 (Over signal), reduce the analog control signal.
What does error Er20 mean on Watson Marlow Pumps Water Pump?
If your Watson Marlow Pumps Water Pump displays error code Er20 (Signal out of range), check the analog control signal range and trim the signal as required.
What does error Err50 mean on Watson Marlow Pumps 630 Water Pump?
If your Watson Marlow Pumps Water Pump displays the error code Err50 (Communication error), try resetting the pump by switching the power off and then on again.
What does error Er4 mean on Watson Marlow Pumps 630?
If your Watson Marlow Pumps Water Pump displays the error code Er 4 (FRAM shadow error), try resetting the pump by switching the power off and then on again.
What does error Er3 mean on Watson Marlow Pumps Water Pump?
If your Watson Marlow Pumps Water Pump displays the error code Er 3 (FLASH corruption), try resetting the pump by switching the power off and then on again.
What does error Er2 mean on Watson Marlow Pumps 630 Water Pump?
If your Watson Marlow Pumps Water Pump displays the error code Er 2 (FLASH write error during drive update), try resetting the pump by switching the power off and then on again.
What does error Er1 mean on Watson Marlow Pumps Water Pump?
If your Watson Marlow Pumps Water Pump displays the error code Er 1 (FRAM corruption), try resetting the pump by switching the power off and then on again.
What does error Er0 mean on Watson Marlow Pumps 630 Water Pump?
If your Watson Marlow Pumps Water Pump displays the error code Er 0 (FRAM write error), try resetting the pump by switching the power off and then on again.
What to do if Watson Marlow Pumps Water Pump runs but there is little or no flow?
If your Watson Marlow Pumps Water Pump runs but produces little to no flow, consider the following: * Ensure fluid is adequately supplied to the pump. * Inspect the lines for any kinks or blockages. * Verify that all valves in the line are open. * Confirm the tube and rotor are correctly placed in the pumphead. * Check the tube for splits or bursts. * Make sure the correct wall-thickness tube is being used. * Verify the direction of rotation is correct. * Check that the rotor isn't slipping on the drive shaft.
Explains symbols for safety instructions, moving parts, hot surface, electric shock, PPE, and WEEE.
Details operating temperature, storage, humidity, altitude, power, voltage, current, fuse, IP, dB, control ratio, max speed.
Site pump on flat, rigid surface with airflow; avoid stacking; consider rotor rotation direction for tube life/pressure.
Guidelines on placement, tubing, suction, speed, recalibration, chemicals, cables, and N module sealing.
Identifies the keypad buttons: Home, Function keys, Up/Down keys, Mode key.
Illustrates how to start and stop the pump using the keypad.
Set voltage selector to 115V or 230V before connecting; check module if N module is fitted.
Table detailing digital/analogue input parameters, frequency range, voltage, current, resistance, and filter bandwidth.
Identifies rear panel features: RJ45 ports, D-sub sensor connector, USB, voltage selector, ON/OFF switch, power cable, fuse.
Details RJ45 connections and LED indications for IP31; describes 9-way D sensor connector wiring.
Scroll to Flow calibration, press CALIBRATE, enter max flow limit, press ENTER.
Set static IP address, subnet mask, and gateway address to suit your network.
Instructions on setting parameters: type value, click set/refresh, navigate pages; lists user-settable parameters.
Ensure sensor is correctly wired to pump before setup; refer to IP31 or IP66 connector sections.
Navigate control settings to Sensor settings, then Configure sensors to select sensor type (Flow/Pressure).
Lists error codes (FRAM, FLASH, Motor stalled, Over current/voltage, Signal out of range) and suggested actions.
Isolate pump, remove pumphead guard; secondary protection via guard switch.
Illustrates continuous tubing replacement for 620R and 620L pumpheads.
Illustrates tube element replacement for 630Du/RE, Sanitary connectors, Industrial connectors, and 630Du/L.
General| Brand | Watson Marlow Pumps |
|---|---|
| Model | 630 Series |
| Category | Water Pump |
| Language | English |
To Next Page