What to do if Watts Premier Water System filter housing leaks?
If water leaks from the blue/white filter housing: * Ensure the bowl is properly tightened. * If there is a kinked o-ring: Turn off the water supply and release the pressure. Replace the o-ring if necessary. Lubricate it and make sure it is seated properly in the filter bowl before reinstalling.
Why is my Watts Premier Water System producing water slowly?
Several factors can cause low or slow water production. Check the following: * Ensure incoming water pressure is at least 40 psi. If it's too low, Watts Premier sells a booster pump. * Confirm the water supply is on and the Adapta Valve is fully open. * Inspect tubing for crimps and straighten or repair them. * Replace clogged pre-filters. * Replace the membrane and Flow Restrictor if the membrane is fouled.
What to do if Watts Premier Water System constantly running and won't shut off?
If your system won't shut off, there are several potential causes: * Low water pressure: Ensure a minimum of 40 psi incoming water pressure. * Crimp in supply tube: Inspect the tubing and straighten or repair as necessary. * High water pressure: Verify that the incoming water pressure does not exceed 80 psi. A pressure relief valve may be required. * High pressure in: Empty the storage tank of water and set the tank air pressure to 5 psi.
Why does my Watts Premier Water System faucet leak from the airgap feature?
Airgap faucet leaks can occur due to: * A crimp in the drain line: Check the tubing. * A restriction in the drain line: Straighten all drain lines, clear any blockages, and cut off any excess tubing. * A clogged drain tube: This is often caused by the dishwasher or garbage disposal. Disconnect the 3/8" black line at the drain, clean it out with a wire, and then reconnect it. Blowing air through the line may not always remove the clog.
Why is my Watts Premier Water System making noise from the faucet or drain?
Noise issues can stem from a few sources: * Air gap faucet: The sound is inherent with air-gap faucets. * Location of drain saddle: Check the diagram for proper location of the drain saddle. * Restriction in drain tube: Clear any blockage that may be caused by debris from the garbage disposal or dishwasher. * High water pressure: A pressure regulator is required if the pressure exceeds 80 psi.
Why is there a small amount of water in my Watts Premier Water System storage tank?
A small amount of water in the storage tank could be due to: * System just starting up: It normally takes 6-10 hours to fill the tank. Low pressure and/or temperature can drastically reduce production rate. * Low water pressure. * Excessive air in the tank bladder: Tank pressure is set at the factory and should be 5 psi when empty. Add air if below 5 psi and bleed air if above 5 psi. Check only when the tank is empty.
Why is the water from my Watts Premier Water System milky colored?
Milky colored water is often due to air in the system. This is normal when initially starting up the RO system and should disappear within 1-2 weeks of normal use. If it reoccurs after filter changes, drain the tank 1 to 2 times.
Detailed instructions for drilling a faucet hole in a porcelain sink.
Procedure for creating a faucet opening in a stainless steel sink.
Steps for installing the Wave Air Gap or non-air gap faucet.
Guide for installing the AG-SS model with monitor faucet.
Instructions for connecting the Adapta Valve to the water supply.
Guidance on securely mounting the RO module within a cabinet.
Steps for installing the drain saddle onto the sink's drain pipe.
Procedure for attaching the tank tee to the system's storage tank.
Connecting the green tube from the RO module to the Adapta Valve.
Connecting the blue tube from the RO module to the storage tank.
Connecting the black tube from the faucet to the drain saddle.
Connecting the red tube from the faucet to the RO membrane housing.
Steps for installing the 6-inch final filter unit.
Instructions for installing the 10-inch final filter.
Guide for initial system setup and activation after installation.
Procedures for performing semi-annual system maintenance.
Steps for annual system upkeep and sanitization.
Detailed guide for replacing the RO membrane.
How to check and adjust air pressure in the storage tank.
Addresses issues with low or slow water output from the system.
Explains the cause and solution for milky or cloudy water.
Troubleshoots situations where the system fails to stop running.
Identifies sources of noise from the faucet or drain connection.
Guides on fixing leaks originating from the faucet's air gap.
Investigates causes for insufficient water accumulation in the tank.
Addresses leaks occurring at the blue or white filter housings.
General| Product Type | Reverse Osmosis System |
|---|---|
| Stages of Filtration | 5 |
| Flow Rate | 50 gallons per day |
| Installation Type | Under Sink |
| NSF Certifications | NSF/ANSI Standard 58 |
| Membrane Type | Thin Film Composite (TFC) |
| Filter Technology | Carbon Block |
| Included Components | Faucet, Tank, Filters |
| Filter Life | 6-12 months (Pre and Post Filters), 2-5 years (Membrane) |
| Weight | 25 pounds |
To Next Page
