WBOX Technologies 0E-RCKMT2200 User Manual

COPYRIGHT © 2019 ADI
USER’S MANUAL
Rackmount Series
0E-RCKMT1000 / 0E-RCKMT1500 / 0E-RCKMT2200
K01-1101046-02
EN

WBOX Technologies 0E-RCKMT2200 Specifications

General

VA	2200VA
Input Voltage	120V
Output Voltage	120V
Battery Type	Sealed Lead Acid
Battery Quantity	2
Transfer Time	4-6ms
Capacity	2200VA
Communication Interface	USB

Summary

IMPORTANT SAFETY INSTRUCTIONS

General Safety Precautions

Covers installation, temperature, humidity, grounding, and circuit protection for fire/shock prevention.

Equipment Handling and Usage Warnings

Covers cover removal, battery service, EPO, laser printers, heat sources, ventilation, aquarium, and medical equipment use.

California Proposition 65 Warning

Advises on chemical exposure risks as per California law.

INSTALLING YOUR UPS SYSTEM

Unpacking and Contents

Lists all items included in the UPS packaging.

Automatic Voltage Regulator (AVR) Explanation

Describes the function of AVR in stabilizing input power fluctuations.

System Block Diagram

Provides a visual overview of the UPS internal components and data flow.

Hardware Installation Guide

Step-by-step instructions for physically installing the UPS and connected equipment.

INSTALLING YOUR UPS SYSTEM (continued)

Power Connection and Circuit Requirements

Details on connecting the UPS to a grounded receptacle and appropriate circuit protection.

Power Switch Operation and Overload Handling

Instructions for turning the UPS on and managing overload conditions.

Battery Charging and Long-Term Storage

Recommendations for optimal battery charging and proper storage procedures.

Computer Communication Ports

Explains the Serial and USB ports for connecting to a computer for management.

Emergency Power Off (EPO) Port Wiring

Instructions for correctly wiring the EPO remote switch for emergency shutdown.

BASIC OPERATION

Front and Rear Panel Component Identification

Identifies and describes key components on the UPS front and rear panels.

BASIC OPERATION (continued)

USB Port and Communication

Details on the USB port for PC connectivity and Power Management Software.

Emergency Power Off (EPO) Port Function

Explains how to use the EPO port for remote emergency shutdown.

Surge Protected Communication Ports

Describes the protection offered for RJ11/RJ45 data and telephone lines.

Wiring Fault Indicator and Grounding

Explains the wiring fault LED and the use of the TVSS screw for grounding.

BATTERY REPLACEMENT

Battery Replacement Safety and Precautions

Outlines critical safety measures and warnings before starting battery replacement.

Battery Replacement Procedure Steps

Provides a detailed, step-by-step guide for replacing the UPS battery.

Battery Wiring Instructions

Specifies the correct method for connecting the battery cables (red to positive, black to negative).

DEFINITION FOR ILLUMINATED LCD INDICATORS

LCD Indicator Meanings and Functions

Explains the various icons, symbols, and readings displayed on the UPS LCD screen.

LCD SETUP FUCTIONS

General Mode and LCD Wake-up

Describes how to check UPS status in general mode and wake the LCD from sleep.

Set-Up Mode Navigation

Details the steps to enter, navigate, and select functions within the UPS setup menu.

Output Quality Settings

Explains the options for configuring the UPS's output quality characteristics.

LCD SETUP FUCTIONS (continued)

Transfer Point and Sensitivity Settings

Covers configuration of voltage transfer points and sensitivity for battery switching.

Self-Test, Buzzer, and LCD Sleeping Mode

Details settings for performing self-tests, managing audible alarms, and display behavior.

Restore Factory Defaults

Instructions on how to reset the UPS to its original factory default settings.

FAULT WARNING DISPLAY AND ALARM

Shutdown Warnings and Alarms

Explains LCD messages and audible alarms that occur during UPS shutdown.

Post-Shutdown Error Codes

Lists error codes displayed on the LCD after shutdown and their potential causes.

TROUBLESHOOTING

Power Outlet and Runtime Issues

Provides solutions for equipment not receiving power or short UPS runtime.

UPS Power-On and Software Issues

Troubleshooting steps for UPS not turning on or inactive power management software.

TECHNICAL SPECIFICATIONS

Input and Output Specifications

Details on voltage ranges, frequency, plug types, output capacity, and receptacles.

Surge Protection, Battery, and Environment

Specifications for lightning/surge protection, battery type, and environmental operating conditions.

Management, Physical, and Safety Specs

Details on management features, physical dimensions, weight, and safety certifications.

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

General Limited Warranty Terms

Outlines ADI's standard warranty coverage for W Box Technologies products.

Specific Product Category Warranties

Lists the warranty periods applicable to different product categories sold by ADI.

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE (continued)

Warranty Exclusions and Liability Limits

Details what is not covered by the warranty and the limitations on ADI's liability.

Liability to Buyer's Customers

Explains the buyer's responsibility to limit ADI's liability towards their end customers.

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE (continued)

Product Returns and Replacement Policy

Describes the procedures for returning defective products for replacement or credit.

Governing Law and Miscellaneous Provisions

Specifies the governing law for the warranty and other general legal clauses.

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE (continued)

Connected Equipment Guarantee Claims

Outlines the process for opening a claim under the Connected Equipment Guarantee.

Claim Filing and Resolution Process

Details on submitting claims, required documentation, and how CyberPower resolves issues.

SAFETY COMPLIANCE STATEMENT

FCC Compliance Statement

Provides regulatory information regarding the device's compliance with FCC rules.