To Next PageTo Next PageWhat to do if the weinor Accessories hand-held transmitter is not sending travel commands?
If your weinor Accessories hand-held transmitter isn't sending travel commands, it could be due to several reasons: the wind alarm might be active (wait 15 minutes), the batteries in the transmitter might be flat (change battery), or the motor may lack power or be overheated (check power supply or allow motor to cool down).
Why does my weinor Accessories blind automatically go up in manual mode?
If your weinor Accessories blind travels up automatically in manual mode, it could be due to several reasons: the wind or rain alarm may be active (wait 15 minutes), the rain sensor may be dirty (clean the rain sensor), there may be a poor radio connection (change the position of the device), or the voltage supply may be interrupted (check the voltage).
What to do if my weinor Accessories blind doesn’t travel down in response to sunshine?
If your weinor Accessories blind isn’t responding to sunshine, it could be because the LIGHT threshold value isn't exceeded (adjust the LIGHT threshold value), the wind or rain alarm is active (wait 15 minutes), the roller shutter mode isn't supported (change the mode), the transmitter is in MANUAL mode (set to AUTOMATIC), there's a poor radio connection (change device position), or the light sensor is dirty (clean it).
How to fix if weinor Accessories device cannot be programmed to recognize the receiver?
If your weinor Accessories device can't be programmed to recognize the receiver, it might already be programmed (delete the device and re-program it) or there could be a poor radio connection (change the position of the device).
Why is my weinor Accessories blind not going up when it's windy?
If your weinor Accessories blind isn't traveling up when it's windy, the WIND threshold value might be set incorrectly. Adjust the WIND threshold value.
What to do if my weinor Accessories blind doesn’t travel down in response to darkness?
If your weinor Accessories blind isn’t traveling down in response to darkness, it could be that the twilight threshold value is set incorrectly (adjust the twilight threshold value) or the twilight function isn't supported by the receiver (use a different receiver).
Why does my weinor Accessories blind travel down when it is windy?
If your weinor Accessories blind travels down when it is windy, the device might be improperly programmed. Delete the device and re-program it.
What does it mean when all LEDs are flashing on my weinor Accessories device?
If all the LEDs are flashing on your weinor Accessories device, it could indicate that the wind sensor is wet or the device is defective. Allow the wind sensor to dry.
General| Brand | weinor |
|---|---|
| Model | BiSens SWR-230V |
| Category | Accessories |
| Language | English |
Operator must read and understand instructions for safe and proper operation.
Do not operate damaged devices; report transport damage immediately.
Adhere to regulations; installation by trained personnel only.
Ensure visibility of system operation and keep controls away from children/disabled.
Use radio systems only where interference-free and safe.
Fasten the device to the roof or façade using the tilting wall bracket.
Device is intended for controlling awnings, blinds, and roller shutters.
Details included components and optional accessories.
Provides operating voltage, temperature range, IP code, radio frequency, weight, and dimensions.
Mount the device to a mast of 27 mm diameter.
Use to attach the device to the corner of the façade or to the mast.
Select operating modes: Awning, Protection, or Roller Shutter.
Procedure for programming transmitters to the device.
Set light threshold for automatic awning retraction based on light levels.
Set wind speed thresholds for automatic awning retraction.
Set rain thresholds for automatic awning retraction.
Set twilight thresholds for automatic awning retraction based on darkness.
Test light function responsiveness by simulating light changes.
Test wind function responsiveness by simulating wind conditions.
Measures rain volume and compares it to the threshold value.
Test rain function responsiveness by simulating rain conditions.
Procedure to remove programmed sensors from the device.
Device is maintenance-free; clean cover with a moist cloth.
Dispose of the device according to applicable regulations.
