Weller WT2010M - User Group Specifics; Work Step vs. User Group

20
Store your soldering tool in a safe place. When not in
use,unitsandtoolsshouldbestoredinadry,highorlocked
area out of the reach of children. Make sure that unused
soldering tools are free of voltage and de-pressurised.
The power cable must only be plugged into the power
socket or adapter approved for this purpose. Checkto
seeifthemainsvoltagematchestheratingsonthe
nameplate.Makesurethemachineisswitchedobefore
pluggingin.
Do not use the cable for purposes other than those for
which it is intended.Nevercarrytheunitbythecable.Do
not use the cable to pull the plug out of the socket. Protect
the cable against heat, oil and sharp edges..
Be alert. Payattentiontowhatyouaredoing.Besmart
whenusingtheunit.Donotusethesolderingtoolifyouare
havingdifcultyconcentrating.
Avoid abnormal posture. Arrangeyourworkstationinan
ergonomicallycorrectway.Avoidbadposturewhenusingthe
unit, as this can lead to postural problems.
The soldering tool must be operated only in perfect
technical working order.Safetydevicesmustnotbe
deactivated.
Faults and defects must be repaired immediately.
Beforeusingtheunit/tool,safetydevicesmustbecarefully
checkedtomakesurethattheyarefunctioningproperlyand
in the manner intended. Check that moving parts are func-
tioningproperlyandarenotsticking,andwhetherpartsare
damaged.Allpartsmustbecorrectlyttedandmustsatisfy
alltherequirementsnecessarytoguaranteetroublefree
operation of the unit.
Use the correct tool. Useonlyaccessoriesorauxiliaryde-
vices which are included in the list of accessories or appro-
vedforusebythemanufacturer.UseWELLERaccessories
orauxiliarydevicesonoriginalWELLERequipmentonly.The
useofothertoolsandotheraccessoriescancauseinjury.
Secure the tool.Useclampingxturestoholdthe
workpiece.
Use a solder fume extraction unit. If appliances for
connecting solder fume extraction units are available, ensure
thattheyareconnectedandusedproperly.
Specied Conditions Of Use
SupplyunitforWELLERsolderingtools.Usethesoldering
stationonlyforthepurposeofsoldering,asspeciedinthe
OperatingInstructions.
Thisdevicemayonlybeusedatroomtemperatureand
indoors. Protect against moisture and direct sunlight.
User groups
Due to differing degrees of risk and potential hazards, sever-
alworkstepsmayonlybeperformedbytrainedexperts.
Work step User groups
Default soldering para-
meters
Specialist personnel with
technical training
Replacing electrical repla-
cement parts
Electricians
Default maintenance
intervals
Safetyexpert
Operation Non-specialists
Operation
Replacing electrical repla-
cement parts
Technical trainees under the
guidance and supervision of a
trained expert
Care and maintenance
WARNING
Before doing any work on the machine, pull the plug out
of the socket. Leave the unit to cool down.
Check all connected cables and hoses on a regular basis. If
powertoolsaredamaged,theymustbeimmediately
removed from use.
Repairs must always be referred to a Weller-trained
specialist.
Useoriginalreplacementpartsonly.
Warranty
Claimsbythebuyerforphysicaldefectsaretime-barred
afteraperiodofoneyearfromdeliverytothebuyer.This
doesnotapplytoclaimsbythebuyerforindemnicationin
accordance with §§ 478, 479 BGB (German Federal Law
Gazette).
Weshallonlybeliableforclaimsarisingfromawarranty
furnishedbyusifthequalityordurabilitywarrantyhasbeen
furnishedbyuseinwritingandusingtheterm„Warranty“.
Thewarrantyshallbevoidifdamageisduetoimproperuse
andifthedevicehasbeentamperedwithbyunauthorised
persons.
For more information please visit
www.weller-tools.com.
EN
ENGLISH