Westerbeke 30 - Page 29

28
SPECIFICATIONS - con tin u e d
FUEL SYSTEM
Lift pump •.
Type
Static pressure (no delivery) ..
Injection pump
1st type
..
2nd type ..
3rd type ..
Injectors ..
Nozzle type: Early engines
Later engines
Nozzle holder
type: Early engines •.
Opening pressure
Main filter
Type
Later
engines
Static injection timing ..
CAPACITIES
Sump (including filter) ..
TORQUE WRENCH SETTINGS
Engine
Cylinder head nuts
Main bearing nuts
Big-end bolts
Flywheel nuts
Injector securing nuts
Injector nozzle
nut
Rocker bracket nuts
Manifold nuts
Engine rear distance piece bolts:
" in.
tin ...
Water pump bolts
Fuel injection pump:
Governor housing securing screws
Distributor
rotor screw
Cam advance screw
Drive plate screw:
Direct
Indirect:
A.C.
mechanical.
U.
S Ib./sq. in. (·3S kg./cm.W).
C.A.V.
DPA.3246496.
DPA.3246776 or DPA.3246776B.
DPA.3246847.
C.A. V. PiDtaux
BDN.O.SPC.6209.
BDN.O.SPC.6389.
DKB.3S.SD.S091.
DKB.3S.SD.SIU.
135 atmospheres.-
C.A.V. bowl-less.
. . FS583602O.
22° B.T.D.C. (fully retarded).
4.5 Quarts
71 lb. ft. (9·8 kg. m.).
75 lb. n. (10·37 kg. m.).
3S lb. n. (4·85 kg. m.).
.. 37 lb. ft. (5007 kg. m.).
12 lb. ft. (1'7 kg. m.).
· . SO lb. n. (70() kg. m.).
· . 25 lb. It. (304 kg. m.).
· . IS lb. ft. (2·1 kg. m.).
.. 20 lb. ft. (2·8 kg. m.).
30 lb. ft. (4·1 kg. m.).
17 lb. ft. (2·3 kg. m.).
· . 40 lb. in. (046 kg. m.).
28 lb. in. (·32 kg. m.).
400 lb. in. (4'6 kg. m.).
160 I b. in. (1'85 kg. m.).
Ring spanner and torque adaptor centres at 2·6 in.
(66 mm.) .. 140 lb. in. ()·61 kg. m.).
Ring spanner and torque adaptor cenlres at 5 in.
(127 mm.)
Transfer pump rotor
End plate set bolt
..
Hydraulic head locating fitting
Advance unit housing cap nut
Advance unit
housing stu(1
Advance unit hOllsing ~pring cap and end plu;; ..
Hydraulic head lockil::~ screw
High-pressure outlet unions
and banjo pipe bolts
Control and 'shut-otT· lever bolt or nut ..
Fuel inlet connection
115 lb. in. (1·32 kg. m.).
65 lb. in. (,75 kg. m.).
.. 45 lb. in. (,52 kg. m.).
· . 35() lb. in. (4'05 kg. m.).
.. 110 lb. in. (1·251.g. m.).
.. 60 lb. in. ('~9 kg. m.).
.. 250 lb. in. (2·9 kg. m.).
.. 170tb.in.tl· 9 6kg.m.).
.. 270 I~. in. (3-l kg. m.).
.. 30 lb. in. (,34 kg. m.).
.. 360 lb. in. (4'15 kg. m.).
• Add 5 atmospheres to the opening pressure when letting new injectOR or after fittin. DeW sprinp to allow Cor settIiDa or tho UUec.or
components
,/ ,"