How to clean red rings and stains on Westinghouse Cooktop?
If you notice red rings, limescale, water rings, discoloration, scratches, shadows, bubbles, or other marks on your Westinghouse Cooktop's ceramic glass surface, it's likely due to improper cleaning. To resolve this, use a ceramic glass cleaner such as Cerapol to correctly clean the cooktop surface.
Why won't my Westinghouse Cooktop cooking zones switch on?
If the Westinghouse Cooktop cooking zones aren't turning on, several factors could be at play. Ensure that no more than 10 seconds have passed since you switched on the appliance or you may need to switch it on again. Check if the child safety device or the lock is activated and deactivate them if so. Avoid touching multiple sensor fields simultaneously; touch only one at a time. Also, remove any objects from the control panel that may be triggering the automatic switch-off function and switch the appliance on again.
What to do if Westinghouse Cooktop beeps and turns on/off?
If your Westinghouse Cooktop is emitting acoustic signals, switching itself on and off repeatedly, it's likely that the On/Off sensor field is covered. Make sure that you do not place any objects on the control panel.
Why is my Westinghouse WHC644BA Cooktop glass pitted?
Pitting on the ceramic glass surface of your Westinghouse Cooktop is likely caused by spillovers of liquids with high sugar content. These spills must be removed immediately using a special scraper for glass. Failure to do so can result in permanent damage to the cooktop glass, which is not covered under warranty.
What does it mean when is lit on Westinghouse WHC644BA Cooktop?
If is lit on your Westinghouse Cooktop, it indicates that either the overheating protection for the cooking zone or the automatic switch-off has been triggered. To resolve this, switch off the cooking zone and then switch it on again.
Why isn't the automatic warm up working on my Westinghouse Cooktop?
If the automatic warm-up function on your Westinghouse Cooktop isn't activating, it could be due to several reasons. First, if there's residual heat on the cooking zone, allow it to cool down. Second, the highest heat setting has the same power as the automatic warm up function. Finally, if the heat setting was set using the sensor field, switch off the cooking zone and set it again using the sensor field.
Why does my Westinghouse WHC644BA Cooktop beep when turned off?
If your Westinghouse Cooktop emits an acoustic signal when switched off, it indicates that the control panel is obstructed. Remove any objects covering the control panel to stop the signal.
Why is the residual heat indicator not working on my Westinghouse Cooktop?
If the residual heat indicator on your Westinghouse Cooktop isn't displaying, it might be because the cooking zone was only on briefly and isn't hot enough. If the cooking zone is supposed to be hot, call the Customer Service Department.
What does it mean when and a number are displayed on Westinghouse WHC644BA Cooktop?
If and a number are displayed on your Westinghouse Cooktop, it suggests an electronics fault. Disconnect the appliance from the electrical supply for a few minutes by removing the fuse. If the issue persists after switching it back on, contact customer service.
Provides crucial safety guidelines for the use and installation of the appliance.
Details precautions for child safety and correct appliance operation.
Instructions on turning the appliance on/off and adjusting heat levels.
Explains the automatic warm-up feature and its duration for different heat settings.
Instructions for activating, deactivating, and overriding the child safety lock.
Details on how to use the timer function for automatic cut-out or countdown.
Steps for setting timer duration and managing countdowns.
Explains the automatic switch-off features for the cooking surface and zones.
Lists common issues, their possible causes, and remedies.
Detailed instructions for the safe and correct electrical connection of the appliance.
General| Brand | Westinghouse |
|---|---|
| Model | WHC644BA |
| Number of Cooking Zones | 4 |
| Voltage | 220-240 V |
| Installation Type | Built-in |
| Control Type | Touch |
| Safety Features | Child Lock, Residual Heat Indicator |
| Dimensions (W x D x H) | 590 x 520 x 46 mm |
| Width | 590 mm |
| Depth | 520 mm |
| Height | 46 mm |
| Color | Black |
| Surface Material | Ceramic Glass |
| Type | Cooktop |
| Frequency | 50 Hz |
To Next Page