Whirlpool FWEB9002IG - Main Component Specifications

7
Washer Combo
capacity /kg
8 9 9.5 10.5 8 9 10.5 11
Washing capacity /kg
Washing
capacity
/kg
Drying
capacity
/kg
Washing
capacity
/kg
Drying
capacity
/kg
Washing
capacity
/kg
Drying
capacity
/kg
Washing
capacity
/kg
Drying
capacity
/kg
capacity
8 9 9.5 10.5 8 5 9 6 10.5 7 11 7
Mixed 6 7 6.5 7 6 5 7 6 7 7 7 7
Quick 1 1 1 1 / / / / / / / /
Wash&dry60′ / / / / 1 1 1 1 1 1 1 1
Gentle 2 3 3 4 2 2 4 2 4 2 4 2
Spin 8 9 9.5 10.5 8 5 9 6 10.5 7 11 7
Stain 3 4 3.5 4 3 3 4 3.5 4 4 4 4
Eco cotton 8 9 9.5 10.5 8 5 9 6 10.5 7 11 7
Wool 2 2 2 2 2 - 2 - 2 - 2 -
Hot air refresh / / / / - 2 - 3 - 3 - 3
Allergy care 4 5 4.5 5 / / / / / / / /
Sanitize wash 6 7 6.5 7 6 4 7 5 7 5 7 5
Drum clean 0 0 0 0 0 0 0 0 0 0 0 0
2． Main components specifications
Component name Specification
drain pump PCX-30G 220-240V 50Hz 30W ；PhilippinePCX-30I 220-240V 60Hz 20W
Power ON/OFF Touch (with automatic power-saving)
Start/pause switch Touch type/push-on
Water level sensor
Frequency range 3.950～4.910±0.016kHz；
Control the water level 0 ～ 310±20mmH
2
O ； Working temperature ： -20℃ ～
70℃
（Radiant、lite+DD）
Washing and spinning motor BLDC motor，sBPM500
Heating pipe for washing 1800W
Heating pipe for drying 1500W
Buzzer Electronic buzzer
Temperature sensor
( Heating for washing)
Resistance R (50 ° C) = 19.73 kΩ
B parameter (25/85 °C) = 3992K
Temperature Sensor
(For drying)
Resistance R (50 °C) = 20.00 kΩ
B parameter (25/100 ° C) = 3900 K
Options switch Touch type
Door lock switch Forcefully opening type, electromagnetic door lock, double-pulse unlocking.
Water inflow valve
(One-way in two-way out ③)
1 ) . Operating water pressure range： 0.02~1.0Mpa
2) Main water inflow 8 L/min, condensing 1.2 L/min (0.5~1.0 MPa, rated voltage)
Water inflow valve
(One-way in three-way out②)
1 ) . Operating water pressure range： 0.02~1.0Mpa
2) Main water inflow, softener flow 9.5L / min, condensing water 1.5 L/min (0.5 ~ 1.0
MPa, rated voltage)
Note:
②The water inlet valve is restrained and just used for drying models.
③ The water inlet valve is restrained and just used for non-drying models.