To Next PageTo Next PageWhy is my Whirlpool HybridCare WED99HEDW humming loudly?
If your Whirlpool dryer is making a loud humming or increased noise during the cycle, it could be due to a tightly packed load. Reduce the load size to the recommended amount and run the dryer for 5–10 minutes.
Why is my Whirlpool HybridCare WED99HEDW Dryer not heating up?
If your Whirlpool dryer isn't heating, the drum may still be turning, but electric dryers require two household fuses or circuit breakers. Check these fuses or breakers and replace or reset them as needed. If the problem persists, contact an electrician to check the 240-volt power supply.
How to fix Whirlpool Dryer that is not drying clothes?
If your Whirlpool dryer isn't drying clothes well or drying times are too long, start by cleaning the lint screen before each load and the HybridCare™ filter after every 5th cycle, along with the screen behind it monthly. Ensure the cooling fan screen is clear and that the dryer is level, allowing clothes to contact the moisture sensors. Avoid overloading the dryer, and check for fabric softener sheets blocking the grille inside the door behind the lint screen. Also, ensure the room temperature stays above 45ºF (7ºC) and that the dryer isn't in a closet without proper ventilation.
Why is my Whirlpool HybridCare WED99HEDW Dryer making a rattling noise?
If your Whirlpool dryer is making a rattling or vibrating noise, check for small objects caught between the edges of the dryer drum and clean out pockets before laundering. Ensure the dryer is properly leveled with all four feet firmly contacting the floor. Also, separate any clothing items that are balled up to allow them to tumble freely.
How to disable control lock on Whirlpool Dryer?
If your Whirlpool dryer displays “Loc” or “Lc”, the Control Lock is enabled. To unlock the controls, touch and hold CONTROL LOCK for 3 seconds. The LED Display will count down 3-2-1, and then clear when unlocked.
Why is my Whirlpool HybridCare WED99HEDW Dryer leaving lint on clothes?
If your Whirlpool dryer is leaving lint on your clothes, clean the lint screen before each load.
Why does my Whirlpool HybridCare WED99HEDW Dryer stain clothes?
If your Whirlpool dryer has stains on the load, it may be due to improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the cycle and avoid using them with steam cycles. Adding fabric softener sheets to a partially dried load can stain garments.
What does the 'Clean HybridCare™ Filter' indicator mean on my Whirlpool HybridCare WED99HEDW?
If the Clean HybridCare™ Filter indicator is lit on your Whirlpool dryer, it means the HybridCare™ Filter and/or lint screen is clogged. Clean the lint screen and the HybridCare™ Filter and screen behind the filter cabinet every 5 cycles for best performance.
Why is the cycle time too short on my Whirlpool HybridCare WED99HEDW?
If your Whirlpool dryer cycle time is too short, ensure the dryer is level so the load contacts the sensor strips on Automatic Cycles. You can also adjust the dryness level setting on Automatic Cycles to increase or decrease drying time.
Why is there water in or around my Whirlpool HybridCare™ Dryer?
If you notice water in the HybridCare™ filter or on the floor near your Whirlpool dryer, ensure the dryer is level with a slope less than 1" (25 mm). Also, check that the HybridCare™ filter is correctly seated in the housing cabinet. Verify the drain hose is no longer than provided and installed no higher than 72" (1.8 m) from the dryer's bottom.
General| Brand | Whirlpool |
|---|---|
| Model | WED99HEDW |
| Capacity | 7.4 cu. ft. |
| Drying Technology | HybridCare |
| Control Type | Electronic |
| Steam Cycle | Yes |
| Energy Star Certified | Yes |
| Width | 27 in |
| Fuel Type | Electric |
| Ventless | No |
| Color | White |
| Dryer Venting | Vented |
| Weight | 140 lbs |
| Type | Dryer |
