Whirlpool LSA 1100 - Error Display and Diagnosis; Check Water Error

RID#1 .5 SUPERSOAK
1)
Super soak option selection improves the Wash performance whenever the
dirt level in the Wash loads found to be higher.
2)
While selecting this Feature, Soak Duration will get increased
to Water level and program selected.
RID#1 .6 SOFTENER FILL
1)
Softener Valve fill will happen in the Last Rinse Phase of all programs except
P5(Wool), P7(Whites) and P10(Spin).
2)
In Case of P8(Colors) Softener valve fill will Happen even in Was
RID#1 .7 DELAY END
1)
Delay End key is used to set the “Delay End” time for the selected wash
program
2)
Delay End option can be selected between 3 to 24 Hrs
3)
While selecting this feature, control will
duration of Delay
RID#2
ERROR DISPLAY & ITS DIAGNOSIS
RID#2
.1 CHECK WATER ERROR
1)
If desired water level did not attain within 10 mins during fill then Check Water Error
will be popped by means of turning ON the Check water LED.
2)
Inlet valve will move to
detection & waits for start key press after checking the water inlet.
3) Need to check:
a) Ensur
e the Water supply at the inlet
b)
Check for the blockage at fill hose and at the Inlet valve filter.
c)
Ensure that Inlet v
inlet valve operation & its connections from PCB to Inlet valve.
d)
Check for pressure sensor frequency response & kink or puncture at the
pressure hose.
e)
Ensure that drain hose free end should be lef
medium.
f)
Ensure that the Water head is >10ft from the Machine Inlet.
g)
Check for functionality of both COLD & SOFTENER VALVE.
ERROR DISPLAY AND DIAGNOSIS
Super soak option selection improves the Wash performance whenever the
dirt level in the Wash loads found to be higher.
While selecting this Feature, Soak Duration will get increased
with respect
to Water level and program selected.
Softener Valve fill will happen in the Last Rinse Phase of all programs except
P5(Wool), P7(Whites) and P10(Spin).
In Case of P8(Colors) Softener valve fill will Happen even in Was
Delay End key is used to set the “Delay End” time for the selected wash
Delay End option can be selected between 3 to 24 Hrs
While selecting this feature, control will
complete the selected cycle in the Specified
ERROR DISPLAY & ITS DIAGNOSIS
.1 CHECK WATER ERROR
If desired water level did not attain within 10 mins during fill then Check Water Error
will be popped by means of turning ON the Check water LED.
Inlet valve will move to
OFF state after 5 mins from Check water error
detection & waits for start key press after checking the water inlet.
e the Water supply at the inlet
Check for the blockage at fill hose and at the Inlet valve filter.
Ensure that Inlet v
alve is turning ON during fill process and if not check for
inlet valve operation & its connections from PCB to Inlet valve.
Check for pressure sensor frequency response & kink or puncture at the
pressure hose.
Ensure that drain hose free end should be lef
t in atmosphere not in any other
Ensure that the Water head is >10ft from the Machine Inlet.
Check for functionality of both COLD & SOFTENER VALVE.
ERROR DISPLAY AND DIAGNOSIS
SERVICE MANUAL
Page | 20
Super soak option selection improves the Wash performance whenever the
with respect
Softener Valve fill will happen in the Last Rinse Phase of all programs except
In Case of P8(Colors) Softener valve fill will Happen even in Was
h Phase
Delay End key is used to set the “Delay End” time for the selected wash
complete the selected cycle in the Specified
If desired water level did not attain within 10 mins during fill then Check Water Error
OFF state after 5 mins from Check water error
detection & waits for start key press after checking the water inlet.
Check for the blockage at fill hose and at the Inlet valve filter.
alve is turning ON during fill process and if not check for
inlet valve operation & its connections from PCB to Inlet valve.
Check for pressure sensor frequency response & kink or puncture at the
t in atmosphere not in any other
Ensure that the Water head is >10ft from the Machine Inlet.
Check for functionality of both COLD & SOFTENER VALVE.