To Next PageTo Next PageHow to fix a Whirlpool W10338647A that won't start?
If your Whirlpool washer won't start, make sure the power cord is correctly plugged into a grounded 3-prong outlet and that there is power to the outlet. Do not use an extension cord. Check the circuit breaker and replace any blown fuses. Remember that the lid must be closed for the washer to run. Also, the washer will pause during certain phases of the cycle, so avoid interrupting it.
Why is my Whirlpool W10338647A Washer not draining properly?
If your Whirlpool washer isn't draining properly, small items may be caught in the pump or between the basket and tub, which can slow draining. Also, cycles with lower spin speeds remove less water than cycles with high spin speeds; use the recommended cycle/speed spin for your garment. Check the drain hose for proper installation, ensuring it's securely attached to the drainpipe or tub, not taped over, and not higher than 96" (2.4 m) above the floor. Remove any clogs from the drain hose.
Why is my Whirlpool W10338647A load not rinsed properly?
If your Whirlpool washer load isn't rinsing properly, ensure that both hot and cold inlet hoses are correctly attached and that water is flowing to the inlet valve. Both hot and cold water faucets must be on. Also, check the inlet valve screens for clogs and remove any kinks in the inlet hose. Using too much detergent or overloading the washer can also prevent proper rinsing. Always measure detergent according to load size and soil level, and avoid tightly packing the load.
What to do if my Whirlpool Washer is not cleaning or removing stains?
If your Whirlpool washer isn't cleaning or removing stains effectively, avoid tightly packing the load. Load garments in loose heaps evenly around the basket wall, using only dry items. Add only 1 or 2 garments after the washer has started. Make sure to add HE detergent, oxi products, and color-safe bleach to the bottom of the basket before adding the load items, and not on top of the load.
What to do if my Whirlpool Washer stops mid-cycle?
If your Whirlpool Washer stops mid-cycle, remember that the washer will pause during certain phases of the cycle. Do not interrupt the cycle. The washer spins the dry load for 2-3 minutes before filling to determine if the load is balanced; the hum of the spins is normal. Ensure you are only using HE detergent, as suds from regular detergents can slow or stop the washer. To remove suds, cancel the cycle, select RINSE & SPIN, and press START/Pause/Unlock, without adding more detergent.
Why is my Whirlpool W10338647A dispenser not working correctly?
If your Whirlpool washer dispenser isn't working correctly, it might be clogged. Use only liquid chlorine bleach in the bleach dispenser and only fabric softener in the fabric softener dispenser.
Why is the lid locked light flashing on my Whirlpool Washer?
If the lid locked light is flashing on your Whirlpool washer, make sure the lid is completely closed. The washer will not start or fill with the lid open. If you stopped or paused a cycle, the lid will not unlock until the basket has stopped spinning, which may take several minutes for large or heavy loads.
How to prevent fabric damage in my Whirlpool Washer?
To prevent fabric damage in your Whirlpool washer, empty pockets, zip zippers, and snap or hook fasteners before washing to avoid snags and tears. Tie all strings and straps before starting the wash load, and mend any rips or broken threads in seams. Avoid tightly packing the load; instead, load garments in loose heaps evenly around the basket wall, using only dry items. Use the cycle designed for the fabrics being washed, and do not pour liquid chlorine bleach directly onto the load. Always read and follow garment manufacturer’s care label instructions.
Why is my laundry tangling in my Whirlpool Washer?
If your laundry is tangling in your Whirlpool washer, load garments in loose heaps evenly around the basket wall. Reduce tangling by mixing types of load items and using the recommended cycle for the garments being washed. You can also select a cycle with a slower wash action and spin speed.
Why is my Whirlpool W10338647A using the wrong water temperature?
If your Whirlpool washer is using the incorrect water temperature, make sure the hot and cold inlet hoses are not reversed. Both hoses must be attached to both the washer and faucet, with both hot and cold water flowing to the inlet valve. Check that the inlet valve screens are not clogged and remove any kinks in the hoses. Note that Energy Star® qualified washers use cooler wash and rinse water temperatures than traditional top-load washers, including cooler hot and warm washes.
General| Type | Top Load Washer |
|---|---|
| Model Number | W10338647A |
| Category | Washer |
| Brand | Whirlpool |
| Product Type | Washer |
| Color | White |
| Capacity | 3.5 cu. ft. |
| Energy Star Certified | Yes |
| Number of Wash Cycles | 12 |
| Control Type | Electronic |
| Voltage | 120 V |
| Width | 27.5 inches |
| Height | 43 inches |
| Depth | 27 in. |
Follow basic precautions to reduce risk of fire, electric shock, or injury when using the washer.
Product contains chemicals known to cause cancer or reproductive harm in California.
Controls and maintains uniform water temperatures based on fabric and soil type.
Includes Extra Rinse and Fabric Softener Added options for wash cycles.
Selects available wash cycles for your laundry load.
Starts, pauses, unlocks the lid, or cancels the cycle.
Shows cycle progress through stages like Sensing, Wash, Rinse, Spin, and Done.
Empty pockets, sort items by recommended cycle, water temp, colorfastness, and separate fabrics.
Add a measured amount of High Efficiency detergent to the bottom of the washer basket before adding clothes.
Load garments in loose heaps evenly around basket wall, do not pack tightly.
Add liquid chlorine bleach to the dispenser, do not overfill, dilute, or use more than 1 cup.
Pour measured liquid fabric softener into dispenser, dilute and select 'Yes' for option.
Turn the cycle knob to choose your wash cycle based on fabric type and load.
Select wash temperature based on fabric type and soils. All rinses are tap cold.
Choose desired cycle options like Extra Rinse and Fabric Softener Added.
Press to start the cycle; press again to pause. Unlock lid after pausing or to add garments.
Replace inlet hoses after 5 years or inspect for damage like bulges, kinks, or leaks.
Monthly cleaning procedure to keep the washer interior odor-free using cleaner or bleach.
Steps to take when not using the washer, including unplugging and turning off water supply.
Procedure to winterize the washer using antifreeze to prevent freezing damage.
Instructions for cleaning the fabric softener and bleach dispensers and the washer exterior.
Steps to shut off water, drain, unplug, and pack the washer for moving.
Procedure to reconnect, level, and run the washer after a period of non-use or moving.
Check installation, levelness, and load balance to resolve vibration or off-balance issues.
Explanation of normal operating sounds like clicking, gurgling, humming, and their causes.
Troubleshoot water leaks by checking installation, fill hoses, drain connection, and plumbing.
Addresses issues like not enough water or the washer not running properly.
Check electrical supply, circuit breakers, and ensure the lid is closed for the washer to run.
Troubleshoot draining/spinning issues due to tight packing, HE detergent, or drain hose installation.
Explanation that high spin speeds can cause dry spots on items near the top of the load.
Check water supply and note Energy Star washers use cooler temperatures.
Ensure proper water supply, check hoses, faucets, and screens for rinsing issues.
Addresses residue on clothes due to load type or detergent use; may require extra rinse.
Tips to prevent tangling by loading evenly, mixing load types, and using correct cycles.
Troubleshoot cleaning issues related to HE detergent, cycle selection, or loading.
Ensure HE detergent, correct cycle, and proper dispenser use for effective cleaning.
Ensures correct use of dispensers for bleach and fabric softener to avoid staining.
Prevent fabric damage by emptying pockets, tying strings, mending rips, and avoiding tight packing.
Address odors by performing monthly maintenance and unloading promptly after cycle completion.
Check lid closure and spinning status; lid unlocks after movement stops.
Details the one-year warranty for parts and labor on defects in materials or workmanship.
Lists conditions and damages not covered by the warranty, such as misuse or cosmetic damage.
Covers implied warranties and limitations on remedies for incidental or consequential damages.
