Whirlpool W10682798A-SP

Questions and Answers

E
Elizabeth SmithAug 17, 2025
How to fix vibration or off-balance in Whirlpool Washer?
- M
  Mary TerrellAug 18, 2025
  If your Whirlpool Washer vibrates or seems off-balance, make sure both the front and rear feet are firmly on the floor, and that the washer is level for proper operation. Check the floor for any flexing or sagging. For uneven flooring, placing a 3/4" (19 mm) piece of plywood under the washer can help reduce noise. Ensure the load is balanced by loading dry items in loose heaps evenly around the basket wall. Avoid adding wet items or too much water, as this can cause imbalance. Wash smaller loads, avoid tightly packing the washer, and don't wash single items. For bulky items like jackets and small comforters, use the Bulky Items/Sheets cycle.
G
Gabriel TateAug 20, 2025
What to do if my Whirlpool W10682798A-SP Washer is leaking?
- M
  Marcus PowellAug 20, 2025
  If your Whirlpool Washer is leaking water, ensure the washer is level to prevent water from splashing out of the basket, and check that the load isn't unbalanced or too tightly packed. Tighten the fill-hose connections and make sure all four fill hose flat washers are properly seated. Ensure the drain hose is correctly connected to the drainpipe or laundry tub, and avoid placing tape over the drain opening. Examine your household plumbing for any leaks or clogs in the sink or drainpipe. If the washer isn't loaded correctly, it can cause the basket to misalign and splash water; refer to the “Using Your Washer” section for proper loading instructions.
J
Jason DavidsonAug 23, 2025
Why is my Whirlpool Washer not draining or spinning?
- R
  Ruth HunterAug 23, 2025
  If your Whirlpool Washer isn’t draining or spinning properly, resulting in wet loads or the spin light staying on, it could be due to several reasons. Small items might be trapped in the pump or between the basket and tub, slowing down drainage; empty pockets and use garment bags for small items. Try using a cycle with a lower spin speed. The washer may be too tightly packed or unbalanced. Also, verify that the plumbing is correctly installed for the drain hose. Excessive detergent can also cause suds that slow or stop draining and spinning.
M
Mark BeasleyAug 26, 2025
Why won't my Whirlpool W10682798A-SP Washer run or fill with water?
- A
  Anthony AnthonyAug 26, 2025
  If your Whirlpool Washer won’t run or fill, stops working, or the wash light remains on, first check for a proper water supply. Both hoses must be attached and have water flowing to the inlet valve. Ensure that both the hot and cold water faucets are turned on. Also, check the inlet valve screens for any clogs and inspect the inlet hoses for kinks that could be restricting water flow.
N
Nicole GibsonAug 27, 2025
What does flashing locked light mean on Whirlpool W10682798A-SP Washer?
- M
  Marc PetersonAug 27, 2025
  If your Whirlpool Washer has a flashing locked light, it means the lid is not closed properly. The washer will not start if the lid is open. If you stopped or paused a cycle using the START/Pause button, the washer may still be spinning. The lid will not unlock until the basket has completely stopped spinning, which may take several minutes, especially with large loads or heavy fabrics.
M
Mary Ellis PhDAug 30, 2025
Why is my Whirlpool Washer load not rinsing?
- B
  Brittany SotoAug 30, 2025
  If your Whirlpool Washer load isn't rinsed properly, start by checking the water supply to ensure the hot and cold inlet hoses aren't reversed. Verify that both hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Inspect the inlet valve screens on the washer for clogs and remove any kinks in the inlet hose. Make sure you're using HE detergent and not using too much, as excessive suds can interfere with proper operation. If the washer is tightly packed, it may not rinse efficiently; consider adding an extra rinse cycle.
J
Juan SmithSep 1, 2025
Why are there dry spots on clothes after Whirlpool W10682798A-SP cycle?
- E
  Eric HughesSep 1, 2025
  If you notice dry spots on your load after a cycle in your Whirlpool Washer, it's likely due to the high-speed spins, which extract more moisture than traditional top-load washers. The combination of high spin speeds and airflow during the final spin can cause items near the top of the load to develop dry spots, which is normal. If this is a concern, and the washer is tightly packed, use the Bulky Items/Sheets or Deep Water Wash cycle for a higher water fill.
R
Renee BowenSep 4, 2025
Why are the wash temperatures wrong on my Whirlpool W10682798A-SP?
- C
  Christina SmithSep 4, 2025
  If you are experiencing incorrect wash or rinse temperatures with your Whirlpool Washer, first ensure that the hot and cold inlet hoses are not reversed. Both hoses must be attached to both the washer and faucet, with hot and cold water flowing to the inlet valve. Check that the inlet valve screens are not clogged and remove any kinks in the hoses. Note that this washer uses cooler wash and rinse water temperatures than older models, including cooler hot and warm washes, to save energy.
L
Lisa Diaz DDSSep 6, 2025
How to prevent fabric damage in Whirlpool W10682798A-SP?
- K
  kimberly01Sep 7, 2025
  If you notice fabric damage after washing in your Whirlpool Washer, ensure that all pockets are empty, zippers are zipped, and fasteners are snapped or hooked before washing to prevent snags and tears. Tie all strings and straps to prevent tangling. Mend any rips or broken threads in seams before washing. Avoid tightly packing the load; instead, load garments loosely and evenly around the basket wall, using only dry items.
C
cnicholsSep 9, 2025
Why does my Whirlpool W10682798A-SP Washer smell?
- M
  Michael HayesSep 9, 2025
  If you are experiencing odors with your Whirlpool Washer, it may be due to not performing monthly maintenance as recommended. See “Washer Care” in Washer Maintenance. Also, ensure you are not using too much detergent; measure correctly and always follow the manufacturer’s directions.

Whirlpool W10682798A-SP Specifications

General

Category	Washer
Brand	Whirlpool
Model Number	W10682798A-SP
Product Type	Top Load Washer
Color	White
Number of Wash Cycles	12
Control Type	Electronic
Delay Wash Option	Yes
Quick Wash Option	Yes
Built-In Water Heater	No
Voltage	120 V
Frequency	60 Hz
Depth	27 in