To Next PageTo Next PageWhat to do if my Whirlpool W10856087A Washer door will not unlock?
Select RINSE & SPIN to remove any water remaining in the washer. The washer door will unlock at the end of the drain. It will take 1 minute for the door to unlock.
Why does my Whirlpool W10856087A keep stopping mid cycle?
If your Whirlpool Washer stops during the cycle and the Start/Pause indicator blinks, it could be due to several reasons: the end of the program with Rinse Hold activated (turn the knob to a spin speed to drain), the cycle being interrupted (close the door and press Start/Pause), the safety system being activated (refer to 'Error Codes'), or the water faucet being closed (open the faucet and check for kinks in the inlet hose).
Why is my Whirlpool Washer not rinsing properly?
If your Whirlpool Washer isn't rinsing properly, it could be because you're not using HE detergent. The suds from non-HE detergent can cause the washer to operate incorrectly. Make sure to use only HE detergent, and always measure it following the manufacturer’s directions based on load size and soil level.
What to do if I see F24 error code on my Whirlpool W10856087A?
If you see error code F24 on your Whirlpool Washer, it may be due to too much laundry for the program or too much inlet water. Select and start the Rinse & Spin program to complete the interrupted wash program. Avoid overloading the washer, following the maximum load size in the 'Program/ Cycle Guide'. If it's due to too much inlet water, turn off the water faucet, hold the Power button for 3 seconds to drain, and turn the faucet back on. If water flows without starting a program, an electrical component has failed, requiring service.
Why does my Whirlpool W10856087A keep pausing?
Your Whirlpool Washer may pause during certain phases of the cycle, which is normal. Avoid interrupting the cycle. The washer may also pause to reduce suds if too much detergent is used, so ensure you're using the correct amount of HE detergent. Also, the door must be completely closed and latched for the washer to run.
Why are my clothes wrinkled after washing in my Whirlpool W10856087A?
If your clothes are wrinkled, twisted, or tangled after washing in your Whirlpool Washer, it could be due to improper loading. Add the load loosely to allow items to move freely. Refer to the 'Cycle Guide' for load size recommendations. Also, try mixing different types of items in the load and using the recommended cycle for the garments being washed.
Why is my Whirlpool W10856087A not spinning and clothes are still wet?
If your Whirlpool Washer isn't spinning and clothes are wet, it could be due to a tightly packed or unbalanced load preventing correct spinning. Check the 'Cycle Guide' for recommended load sizes. Also, make sure you are using HE detergent and following the manufacturer's directions. Too much detergent can also cause this issue. To remove extra suds, select RINSE & SPIN without adding detergent.
Why does the spin speed “0” blink on my Whirlpool Washer?
If the spin speed “0” is blinking on your Whirlpool Washer and the laundry is still very wet, it means an unbalanced load prevented the spin cycle to avoid damage to the washer. Add more laundry items of different sizes and start the Rinse & Spin program. Avoid small loads of a few large, absorbent items and wash different-sized items in one load.
Why is there water left in my Whirlpool W10856087A Washer after the cycle?
If water remains in your Whirlpool Washer after the cycle and the door is locked, select RINSE & SPIN to remove any remaining water. The washer door will unlock at the end of the drain.
Why is my Whirlpool Washer using the wrong water temperature?
If your Whirlpool Washer is using incorrect wash or rinse temperatures, ensure the hose is attached to both the washer and faucet with water flowing to the inlet valve. Check that the inlet valve screen is not clogged and remove any kinks in the hose.
General| Category | Washer |
|---|---|
| Model Number | W10856087A |
| Brand | Whirlpool |
| Product Type | Top Load Washer |
| Color | White |
| Capacity | 4.3 cu. ft. |
| Energy Star Certified | Yes |
| Number of Wash Cycles | 12 |
| Control Type | Electronic |
| Voltage | 120V |
| Frequency | 60Hz |
| Spin Speed | 700 RPM |
| Weight | 120 lbs |
| Dimensions (H x W x D) | 43.5 in x 27 in x 27 in |
Guidance on how to use the washer for daily operation.
Guide to identifying and resolving error codes displayed on the washer.
