What to do if my Whirlpool washing machine Washer won't start and no lights come on?
If your Whirlpool Washer isn't starting and no lights are on, make sure the mains plug is properly inserted into the socket. Also, check if the wall socket is working by testing it with a table lamp. Ensure that you've selected a program correctly and that you've pressed the 'On/Off' button if your model has one.
How to fix a draining out fault on a Whirlpool washing machine Washer?
To address a draining fault with your Whirlpool Washer, first check the drain hose for any kinks. Next, inspect the pump and filter for blockages. Lastly, ensure the drain hose is not frozen.
Why does my Whirlpool washing machine Washer stop during the wash cycle?
If your Whirlpool Washer stops mid-cycle, check if the 'Rinse Hold' lamp is illuminated and, if so, press the button to deactivate this option. Verify that another program hasn't been accidentally selected; if it has, reselect your desired program and press 'Start/Pause'. Also, check if the 'Start/Pause' lamp is flashing and press the 'Start/Pause' button. Ensure the 'On/Off' lamp is on, pressing the 'On/Off' button if it's off. Finally, check if the washing machine safety system has been activated.
What to do if my Whirlpool washing machine Washer won't start, but the 'Start/Pause' light is flashing?
If your Whirlpool Washer isn't starting but the 'Start/Pause' light is flashing, be sure the appliance door is fully closed. Check that the program hasn't been changed. Also, ensure the water tap is open; if it's not, open it and then press the 'Start/Pause' button.
What to do if my Whirlpool washing machine Washer won't start but the 'On/Off' light is on?
If your Whirlpool Washer isn't starting, but the 'On/Off' light is illuminated, verify that the appliance door is properly closed. Also, ensure that a program has been selected and started. Check if the water tap is open; if not, turn the appliance off and then on again.
Why are the spin results poor on my Whirlpool washing machine?
If your Whirlpool Washer leaves laundry too wet after the spin cycle, try adding smaller items to balance the load and repeat the spin cycle. Also, ensure that you are using the correct amount of detergent.
Why is my Whirlpool washing machine vibrating during the spin cycle?
If your Whirlpool Washer is vibrating excessively during the spin cycle, ensure the appliance is level and solidly installed on all four feet. Also, check that the transit bolts have been removed before using the appliance.
What causes a Water Stop fault on a Whirlpool washing machine?
A Water Stop fault on your Whirlpool Washer can be caused by excessive foam. Also, a leak in the inlet hose or within the appliance can trigger it; in such cases, the pump activates automatically to remove the water.
Why is there a water inlet fault in my Whirlpool washing machine?
If you're experiencing a water inlet fault with your Whirlpool Washer, first check that the water tap is fully open and that the water supply pressure is sufficient. Next, inspect the water inlet hose to ensure it's not kinked. Also, check the mesh filters for blockages. Finally, make sure the water inlet hose isn't frozen.
Why are there detergent residues in my Whirlpool washing machine Washer dispenser after washing?
If you find detergent residues in the dispenser of your Whirlpool Washer after a wash, check that the siphon is correctly installed and clean. Also, ensure enough water is being supplied; the mesh filters between the inlet hose and the tap could be blocked. Check and clean the filter two or three times a year.
Verify machine is undamaged and all parts are present after unpacking.
Essential step to prevent interior damage during transport before initial use.
Proper placement and levelling on a solid floor for optimal performance.
Connect cold water supply hose according to local regulations and specifications.
Connect drain hose to siphon or sink edge, avoiding siphoning effects.
Ensure qualified installation to an earthed socket, following safety regulations.
Information on recyclable packaging and proper disposal of the washing machine.
Guidelines for safe operation, cleaning, and child safety measures.
Compliance statement with relevant European Directives for safety and EMC.
Identifies key parts like worktop, control panel, dispenser, door, and filter.
Instructions on how to properly open and close the washing machine door.
How to use the plastic screw to lock or unlock the appliance door.
Steps to run a short wash cycle without laundry to remove residual water.
Guidance on sorting clothes by fabric type, colour, size, and handling delicates.
Advice on emptying pockets and securing closures like zips before washing.
Recommendations for treating stains and using dyes suitable for washing machines.
Instructions on how to load laundry loosely into the drum for optimal washing.
Factors influencing detergent choice and remarks on specific compounds and usage.
Guidance on dosage based on soiling, load size, and water hardness, with a chart.
Explanation of dispenser chambers for various detergents and additives.
Instructions for using liquid detergents, fabric softener, bleach, and starch powder.
Step-by-step guide to safely remove, clean, and reinsert the machine's filter.
Instructions for draining residual water before further operations or maintenance.
How to clean appliance exterior, control panel, and door seal.
Recommendation to regularly check and clean the filter for optimal performance.
Detailed steps for removing, washing, and refitting the detergent dispenser drawer and parts.
Instructions for cleaning mesh filters at the water inlet connection points.
Resolving issues when the appliance does not start or lamps do not light up.
Troubleshooting for appliance stopping during a programme or specific lamps flashing.
Identifying and resolving issues with detergent and additive residues in the dispenser.
Solutions for appliance vibration and poor final spin results, including imbalance.
Diagnosing and resolving problems related to no or insufficient water supply.
How to interpret automatic safety system detections and fault codes.
Detailed steps for resolving water inlet faults, checking tap, hose, and filters.
Troubleshooting steps for draining faults, checking drain hose and pump/filter blockage.
Procedure for electrical module faults and when to contact After-Sales Service.
Causes and resolution for Water Stop faults, including foam or leaks, and pump activation.
Steps before contacting After-Sales Service and required information for support.
Instructions for safely moving the washing machine, including water removal and fitting transit bolts.
Procedure for safely replacing the fuse in the appliance's plug.
Ensuring plug/socket compatibility and seeking professional help for changes.
To Next Page
General