Whirlpool WFC 3C34 P X User Manual (English)

Questions and Answers:

G
Gary PowersAug 12, 2025
What to do if my Whirlpool Dishwasher won’t start or respond to commands?
- R
  Raymond DiazAug 12, 2025
  If your Whirlpool Dishwasher won’t start or respond, try these steps: * Ensure the appliance is properly plugged into the socket. * If there was a power outage, press the START/Pause button to resume the cycle, as the dishwasher doesn't restart automatically. * Make sure the dishwasher door is fully closed until you hear a “click.” * If the cycle was interrupted by opening the door for more than 4 seconds, close the door and press the START/Pause button. * If the display shows F9 or F12 and both On/Off and START/Pause LEDs are blinking rapidly, switch the appliance off and on again after one minute. If the problem continues, unplug the appliance for one minute, then plug it back in.
G
Glenn GilbertAug 16, 2025
What to do if my Whirlpool Dishwasher won’t drain and shows F3 error?
- E
  Emily FreyAug 16, 2025
  If your Whirlpool Dishwasher isn't draining and the display shows F3 with blinking On/Off and START/Pause LEDs, it could be due to several reasons: * The wash cycle might not be finished yet; wait until it completes. * The drain hose could be bent; check and straighten it. * The sink drain pipe might be blocked; clean it. * The filter might be clogged with food residues; clean the filter.
A
Alison MendezAug 19, 2025
Why is my Whirlpool WFC 3C34 P X Dishwasher not filling with water and showing F6 error?
- D
  David DuffyAug 20, 2025
  If your Whirlpool dishwasher isn't filling with water and the display shows F6 with the On/Off and START/Pause LEDs blinking rapidly, it might be due to: * Lack of water supply or a closed tap; ensure the water supply is on. * A bent inlet hose; make sure the inlet hose is not bent. * A clogged sieve in the water inlet hose; clean it, then turn the dishwasher off and on, and restart a new program.
A
Amanda PotterAug 23, 2025
Why are the dishes not clean after using my Whirlpool WFC 3C34 P X Dishwasher?
- S
  Sheri GuerreroAug 25, 2025
  If your Whirlpool dishwasher is not cleaning dishes properly, consider the following: * Ensure the crockery is arranged correctly. * Check that the spray arms can rotate freely without being blocked by dishes. * Select a more appropriate wash cycle. * Make sure you are using the correct amount of detergent and that it is suitable for dishwashers. * Ensure the cap on the rinse aid compartment is properly closed. * Clean the filter assembly if it is soiled or clogged. * Fill the salt reservoir if it is empty.
A
Amber HolmesAug 27, 2025
How to reduce excessive noise from my Whirlpool Dishwasher?
- N
  Nancy LopezAug 27, 2025
  If your Whirlpool Dishwasher is making excessive noise, it could be due to: * Dishes rattling against each other; make sure to position the crockery correctly. * An excessive amount of foam; ensure the detergent is measured correctly and is suitable for dishwashers. Restart the dishwasher by pressing the DRAIN button and run a new program without detergent.
J
James BradleyAug 31, 2025
What to do if my Whirlpool WFC 3C34 P X finishes the cycle prematurely and shows F15 error?
- C
  Cynthia MillerAug 31, 2025
  If your Whirlpool Dishwasher is finishing cycles prematurely and the display shows F15 with the On/Off and START/Pause LEDs blinking, it could be due to: * The drain hose being positioned too low or siphoning into the home sewage system; check the drain hose height and install an air admittance valve if necessary. * Air in the water supply; inspect the water supply for leaks or other issues.
J
James LopezSep 3, 2025
Why is the salt indicator lit on my Whirlpool WFC 3C34 P X Dishwasher?
- M
  Mr. John SmithSep 3, 2025
  The salt indicator light on your Whirlpool Dishwasher may stay on if the salt reservoir is empty. Refill the reservoir with salt. After refilling, the indicator may remain lit for several wash cycles. Also, adjust the water hardness.
J
Jill BartonSep 7, 2025
Why is the rinse aid indicator lit on my Whirlpool Dishwasher?
- E
  ethan85Sep 7, 2025
  The rinse aid indicator light on your Whirlpool Dishwasher may stay on if the rinse aid dispenser is empty. Refill the dispenser with rinse aid; after refilling, the rinse aid indicator may remain lit for several wash cycles.

Whirlpool WFC 3C34 P X Specifications

General

Door color	Stainless steel
Cord length	1.3 m
Display type	LED
Product size	Full size (60 cm)
Built-in display	Yes
Inlet hose length	1.55 m
Custom panel-ready	No
Outlet hose length	1.5 m
Appliance placement	Freestanding
Control panel color	Black
Package weight	49000 g
Cycle time	190 min
Noise level	44 dB
Delay start (max)	24 h
Dishwashing programs	Eco, Intensive 65°C, Pre-wash, Quick, Silent
Number of place settings	14 place settings
Number of washing programs	8
Current	10 A
Connected load	1900 W
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Energy efficiency scale	A to G
Water consumption per cycle	9.5 L
Energy consumption per cycle	0.848 kWh