What does 'rL' mean on my Whirlpool WFW8620HC display?
If the display shows “rL” (remove load), it means a load was detected in the drum during the Clean Washer with affresh® cycle. Remove any items from the washer drum and restart the Clean Washer with affresh® cycle.
What does F# E# error code mean on my Whirlpool Washer?
If the display shows “F# E# or F## E## code other than as described above”, it indicates a system error code. Try touching POWER once to clear the code, then again to restart the washer. If the code appears again, it is recommended to call for service. You can also try unplugging the washer for 30 seconds and then plugging it back in.
How to troubleshoot drain pump error on Whirlpool WFW8620HC Washer?
If the display shows “F9” followed by “E1” or “F09” followed by “E01”, this indicates a drain pump system error. Check the plumbing to ensure the drain hose is correctly installed and doesn't extend more than 4 1/2" (114 mm) into the standpipe. Also, ensure the drain hose isn't kinked, pinched, or blocked, and remove any clogs. Use the drain hose form and securely attach it to the drainpipe or tub. Lower the drain hose if its end is higher than 96" (2.4 m). Finally, make sure you're using only HE detergent and measuring it according to the manufacturer's directions based on load size and soil level.
What to do if my Whirlpool Washer displays a water supply error?
If the display shows “Lo” followed by “FL” or “F8” followed by “E1” or “Lo” followed by “FL” or “F08” followed by “E01”, it indicates a water supply error. The unit will drain for 8 minutes with the door locked, and this drain cycle must finish to reset the error code. Once done, press POWER once to clear the code, then again to restart the washer. If the code reappears, it is recommended to call for service. Also, ensure that both inlet hoses are properly attached and that water is flowing to the inlet valve, and both hot and cold water faucets are turned on. Check the inlet valve screens for clogs, remove any kinks in the inlet hose, and ensure auto shut-off connectors and hoses are correctly installed and functioning. Use only the manufacturer’s recommended inlet hoses.
What to do if “Sd” or “SUD” (excess suds) appears on my Whirlpool WFW8620HC Washer?
If the Whirlpool Washer displays “Sd” or “SUD,” it means there are too many suds. The washer is trying to reduce them. Let the washer continue its cycle. Make sure you're only using HE detergent and follow the detergent manufacturer’s instructions to determine the correct amount based on your load size. If the issue continues, consider switching to a different HE detergent.
Why my Whirlpool Washer won’t start or fill with water?
If your Whirlpool washer won’t run or fill, or it stops working, ensure both inlet hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Check the inlet valve screens for clogs and remove any kinks in the inlet hoses. Verify the power cord is plugged into a grounded 3-prong outlet, avoid using an extension cord or GFCI, and ensure the outlet has power. If problems persist, have an electrician check the voltage and reset any tripped circuit breakers or replace blown fuses.
How to stop my Whirlpool WFW8620HC Washer from vibrating?
To resolve excessive vibration, rocking, or “walking” in your Whirlpool washer: * Ensure the front and rear feet are firmly in contact with the floor and locked, with the jam nuts tight against the cabinet bottom. * Check the floor for flexing or sagging. If uneven, use a 3/4" (19 mm) piece of plywood underneath the washer. Avoid raised wooden platforms. * Avoid tightly packed or excessively large loads, and balance single items like rugs with a few extra items. * Make sure you have removed the shipping bolts from the back of the washer.
Why won't the door lock on my Whirlpool WFW8620HC Washer?
If the display shows “F5” followed by “E2” or “F05” followed by “E02”, it means the washer door isn't locking. Press POWER to cancel the cycle. Make sure the door is fully closed and latched, and check inside the drum for items that might be preventing the door from closing properly.
General| Style | front load |
|---|---|
| Color | chrome shadow |
| Washer Capacity | 5 cu. ft. |
| Max Spin Speed | 1, 100 |
| Spin Speeds | 5 |
| Number of Cycles | 37; 12 (regular, normal, delicates, wrinkle control, bulky items, heavy duty, whites, sanitize, colors, cold wash, towels, quick) |
| Number of Options | 11 |
| Temperature Settings | 5 |
| Soil Levels | 3 |
| Internal Heater | no |
| Control Panel | touchpad |
| Cycle Signal | yes |
| Interior Light | no; led |
| Steam | yes |
| Add Wash | yes |
| Soak Settings | yes |
| Remote Control | no |
| Wi-Fi | no |
| Voltage | 120 volts |
| Frequency | 60 hz |
| Current | 15a |
Weight and Dimensions| Depth | 33 1/4 inch |
|---|---|
| Height | 38 5/8 inch |
| Width | 27 inch |
Crucial safety guidelines to follow before and during washer use to prevent hazards.
Details on optional accessories like pedestals for height adjustment and stack kits for space saving.
Explains how to select wash programs, modifiers, and additional options.
Describes display indicators, cycle progress, and special utility cycles.
Information on automatic dispensing systems and single-load compartments.
Guide on selecting wash programs based on fabric type and desired washing method.
Explains how to select and adjust detergent concentration for optimal cleaning.
Instructions for filling the Load & Go bulk and single load dispensers.
Steps for sorting, preparing, loading laundry, and adding products.
How to choose wash programs, modifiers, and additional options.
Instructions for starting, pausing, and managing wash cycles.
Guidelines for maintaining water inlet hoses and cleaning the door seal.
Procedures for cleaning the inside of the washer and its components.
Preparing the washer for periods of inactivity or winter conditions.
Steps to drain residual water and clean the drain pump filter.
Explains error codes for diagnosing washer malfunctions.
Solutions for problems related to washer movement, sounds, and water leaks.
Addresses improper filling, draining, spinning, and load balancing.
Solutions for poor cleaning, stains, odors, and fabric damage.
Troubleshooting for unresponsive controls, dispenser problems, and cycle time variations.
Solutions for clothes not drying satisfactorily or taking too long.
Tips for removing lint and preventing wrinkles in dried loads.
Details what fabrication defects are covered and what is excluded from the warranty.
Conditions for warranty validity, how to make a claim, and warranty term.
Information on how to contact Whirlpool for advice, service, and finding product details.
To Next Page
