To Next PageTo Next PageWhy is the remote control not working for my Whirlpool WHAW101BW?
If the remote control for your Whirlpool Air Conditioner isn't working, check if the batteries are inserted correctly, ensuring they are in the right direction. If the batteries are dead, replace them and dispose of the old ones responsibly.
Why my Whirlpool WHAW101BW will not start?
If your Whirlpool Air Conditioner won't start, check these potential causes: * Ensure the power cord is properly plugged into a grounded 3-prong outlet. * Inspect the house fuse or circuit breaker box; replace the fuse or reset the breaker if necessary. * In case of a power failure, the unit will restart automatically after power is restored, but there's a 3-minute protective delay to prevent compressor overload. * Check the power cord reset button. If it trips, press it to reset. If it won't stay engaged, stop using the air conditioner and contact a qualified technician.
What to do if my Whirlpool WHAW101BW Air Conditioner is not cooling properly?
If your Whirlpool Air Conditioner isn't cooling properly, consider the following: * Ensure that curtains, blinds, or furniture aren't blocking the front of the unit. * Lower the thermostat temperature setting. * Clean the air filter. Refer to the “Air Conditioner Care” section for instructions. * Allow sufficient time for the room to cool down after turning on the air conditioner. * Close any open doors or windows to prevent warm air from entering. * If the cooling coils are frozen, consult “The Air Conditioner Is Freezing Up” for guidance.
Why is my Whirlpool Air Conditioner remote control not working?
If your Whirlpool Air Conditioner remote control isn't working, check if the batteries are inserted correctly, ensuring they are in the right direction. If they are, the batteries might be dead. Replace them and dispose of the old ones responsibly.
How to fix a Whirlpool WHAW101BW that is freezing up?
If your Whirlpool Air Conditioner is freezing up, it's likely due to ice blocking the airflow. Turn off the unit and allow it to thaw completely. Once the ice has melted, operate the unit on a higher fan speed. If the issue persists, contact customer service for further assistance.
Why is my Whirlpool WHAW101BW dripping water outside?
If water is dripping from the outdoor side of your Whirlpool Air Conditioner, it's likely normal during hot and humid weather. This occurs due to condensation. Do not drill a hole into the bottom of the metal base pan, as this will reduce cooling performance.
What to do if my Whirlpool WHAW101BW is dripping water inside the room?
If water is dripping inside the room from your Whirlpool Air Conditioner, it might not be properly leveled. Ensure the unit slopes slightly downward toward the outside to allow for proper drainage. Refer to the “Installation Instructions” section for guidance on leveling. Do not drill a hole into the bottom of the metal base pan, as this will reduce cooling performance.
Why does water collect in the base pan of my Whirlpool Air Conditioner?
If water collects in the base pan of your Whirlpool Air Conditioner, it's normal. The moisture removed from the air gathers there and evaporates to the outside, aiding the cooling process. Do not drill a hole into the bottom of the metal base pan, as this will reduce cooling performance.
General| Type | window |
|---|---|
| Operating Area Size | 450 square feet |
| Cooling Capacity | 10000 british thermal units |
| Cooling Settings | 3 |
| Heater | no |
| Fan Speeds | 3 |
| Fan Airflow Rate | 282 cubic feet per minute |
| Remote Control | yes |
| Timer | yes |
| Sleeping Mode | yes |
| Energy Efficiency | 12.1 |
Details electrical specifications applicable to all models.
Specifies electrical needs for 230-volt air conditioner models.
Outlines electrical specifications for 115-volt air conditioner models.
Explains the proper grounding procedures for safe operation.
Instructions for attaching and fitting the side curtains for the unit.
Steps for placing and securing the air conditioner unit within the window opening.
Steps to ready the unit for installation, involving panel removal.
Criteria for choosing the optimal location for wall installation.
Steps for preparing the wall opening and framing for the unit.
Explains what the one-year warranty covers and exclusions.
Lists items and conditions not covered by the XLS Products warranty.
