To Next PageTo Next PageWhy is the remote control not working for my Whirlpool WHAW121BW?
If the remote control for your Whirlpool Air Conditioner isn't working, check if the batteries are inserted correctly, ensuring they are in the right direction. If the batteries are dead, replace them and dispose of the old ones responsibly.
Why my Whirlpool WHAW121BW Air Conditioner will not start?
If your Whirlpool Air Conditioner won't start, check these potential causes: * Ensure the power cord is properly plugged into a grounded 3-prong outlet. * Inspect the house fuse or circuit breaker box; replace the fuse or reset the breaker if necessary. * In case of a power failure, the unit will restart automatically after power is restored, but there's a 3-minute protective delay to prevent compressor overload. * Check the power cord reset button. If it trips, press it to reset. If it won't stay engaged, stop using the air conditioner and contact a qualified technician.
Why is my Whirlpool WHAW121BW Air Conditioner remote control not working?
If your Whirlpool Air Conditioner remote control isn't working, check if the batteries are inserted correctly, ensuring they are in the right direction. If they are, the batteries might be dead. Replace them and dispose of the old ones responsibly.
How to fix a Whirlpool WHAW121BW Air Conditioner that is freezing up?
If your Whirlpool Air Conditioner is freezing up, it's likely due to ice blocking the airflow. Turn off the unit and allow it to thaw completely. Once the ice has melted, operate the unit on a higher fan speed. If the issue persists, contact customer service for further assistance.
Why is my Whirlpool Air Conditioner dripping water outside?
If water is dripping from the outdoor side of your Whirlpool Air Conditioner, it's likely normal during hot and humid weather. This occurs due to condensation. Do not drill a hole into the bottom of the metal base pan, as this will reduce cooling performance.
What to do if my Whirlpool Air Conditioner is dripping water inside the room?
If water is dripping inside the room from your Whirlpool Air Conditioner, it might not be properly leveled. Ensure the unit slopes slightly downward toward the outside to allow for proper drainage. Refer to the “Installation Instructions” section for guidance on leveling. Do not drill a hole into the bottom of the metal base pan, as this will reduce cooling performance.
Why does water collect in the base pan of my Whirlpool WHAW121BW?
If water collects in the base pan of your Whirlpool Air Conditioner, it's normal. The moisture removed from the air gathers there and evaporates to the outside, aiding the cooling process. Do not drill a hole into the bottom of the metal base pan, as this will reduce cooling performance.
What to do if my Whirlpool Air Conditioner is not cooling properly?
If your Whirlpool Air Conditioner isn't cooling properly, consider the following: * Ensure that curtains, blinds, or furniture aren't blocking the front of the unit. * Lower the thermostat temperature setting. * Clean the air filter. Refer to the “Air Conditioner Care” section for instructions. * Allow sufficient time for the room to cool down after turning on the air conditioner. * Close any open doors or windows to prevent warm air from entering. * If the cooling coils are frozen, consult “The Air Conditioner Is Freezing Up” for guidance.
General| Type | window |
|---|---|
| Operating Area Size | 550 square feet |
| Cooling Capacity | 12000 british thermal units |
| Cooling Settings | 3 |
| Heater | no |
| Fan Speeds | 3 |
| Fan Airflow Rate | 270 cubic feet per minute |
| Remote Control | yes |
| Timer | yes |
| Sleeping Mode | yes |
| Energy Efficiency | 12.1 |
Basic precautions to reduce risk of fire, electrical shock, or injury.
General electrical safety and requirements for all models.
Electrical specifications and requirements for 230V air conditioner models.
Electrical specifications and requirements for 115V air conditioner models.
Guidance on the proper and safe grounding of the air conditioner unit.
Safety precautions and testing procedures for the air conditioner's power supply cord.
Criteria for selecting a suitable location for window installation.
Steps to unpack and prepare the larger air conditioner unit for installation.
Reinserting the chassis and reassembling the air conditioner unit.
Guidelines for choosing an appropriate location for wall installation.
Securing the cabinet and reinstalling the air conditioner chassis.
How to choose and set fan speed and operating modes (Cool, Dry, Fan).
Instructions for increasing or decreasing the set temperature.
Setting delayed shutoff or start times for the air conditioner.
Using remote for power, cool mode, and fan speed adjustments.
Utilizing advanced modes like Eco, Sleep, Auto, and Timer via remote.
Troubleshooting steps for when the air conditioner fails to power on.
Solutions for issues where the unit is not cooling effectively.
Diagnosing and resolving problems related to the cooling coils freezing.
