Whirlpool WTW4850BW User Manual (English)

Questions and Answers:

A
Anthony BryanAug 22, 2025
What to do if my Whirlpool Washer won't run or fill?
- J
  Janet MurphyAug 22, 2025
  If your Whirlpool Washer won't run or fill, consider the following: * Check for proper water supply - both hoses must be attached and have water flowing to the inlet valve. * Ensure both hot and cold water faucets are turned on. * Check that inlet valve screens have not become clogged. * Check for any kinks in the inlet hoses, which can restrict water flow. * Plug the power cord into a grounded 3-prong outlet and do not use an extension cord. * Ensure there is power to the outlet and reset a tripped circuit breaker or replace any blown fuses. If problems continue, contact an electrician. * Make sure the lid is closed for the washer to run. * Note that the washer will pause during certain phases of the cycle, so do not interrupt the cycle.
J
James Vasquez IIAug 26, 2025
Why is my Whirlpool WTW4850BW leaking water?
- L
  Leslie LopezAug 26, 2025
  If your Whirlpool Washer is leaking water, here are some things to check: * Ensure the washer is level, as water may splash off the basket if it is not. Also, check that the load is not unbalanced or tightly packed. * Tighten the fill-hose connections. * Make sure all four fill hose flat washers are properly seated. * Pull the drain hose from the washer cabinet and properly secure it to the drainpipe or laundry tub. Do not place tape over the drain opening. * Check household plumbing for leaks or a clogged sink or drain, as water can back up out of a clogged sink or drainpipe. * Ensure the washer is loaded as recommended, as improper loading can cause the basket to be out of alignment and cause water to splash off the tub.
W
watsonsonyaAug 27, 2025
Why is the locked light flashing on my Whirlpool WTW4850BW Washer?
- D
  Darrell JenkinsAug 27, 2025
  If the locked light is flashing on your Whirlpool Washer: * Ensure the lid is closed. The washer will not start or fill with the lid open. * If a cycle was stopped or paused using the Start/Pause button, the washer may still be spinning. The lid will not unlock until the basket has stopped spinning, which may take several minutes if washing large loads or heavy fabrics.
S
Scott PerezAug 31, 2025
Why is my Whirlpool WTW4850BW Washer not rinsing the load?
- D
  David FischerAug 31, 2025
  If your Whirlpool Washer is not rinsing the load properly: * Check for proper water supply. Make sure hot and cold inlet hoses are not reversed. Both hoses must be attached and have water flowing to the inlet valve. Both hot and cold water faucets must be on. * Ensure that the inlet valve screens on the washer are not clogged. Remove any kinks in the inlet hose. * Using too much detergent can prevent the washer from operating correctly. Always measure detergent and follow detergent directions based on load size and soil level. * The washer is less efficient at rinsing when the load is tightly packed.
B
brittanymorganSep 1, 2025
How to prevent fabric damage when using Whirlpool WTW4850BW?
- T
  Tyler RileySep 1, 2025
  To prevent fabric damage when using your Whirlpool Washer: * Empty pockets, zip zippers, and snap or hook fasteners before washing to avoid snags and tears. * Tie all strings and straps before starting the wash load. * Mend rips and broken threads in seams before washing. * Load garments in loose heaps evenly around the basket wall. Load with dry items only. * Use a cycle designed for the fabrics being washed. * Add only 1 or 2 additional garments after the washer has started. * Do not pour liquid chlorine bleach directly onto the load. Wipe up bleach spills, as undiluted bleach will damage fabrics. Do not use more bleach than recommended by the manufacturer. * Do not place load items on top of the bleach dispenser when loading and unloading the washer.
W
wmiddletonSep 3, 2025
Why is there sand, pet hair, or lint on my load after washing in Whirlpool Washer?
- C
  Cathy Smith PhDSep 3, 2025
  If you find sand, pet hair, lint, etc. on the load after washing in your Whirlpool Washer, it is possible that heavy sand, pet hair, lint, and detergent or bleach residues may require additional rinsing. Select 2 Rinses for the selected cycle.
S
Sherry GlennSep 5, 2025
Why does my Whirlpool Washer have odors?
- E
  ebrownSep 5, 2025
  Odors in your Whirlpool Washer can occur due to a few reasons: * Monthly maintenance was not performed as recommended. See 'Washer Care' in Washer Maintenance. * The washer is not unloaded as soon as the cycle is complete. * Too much detergent is being used. Be sure to measure correctly and always follow the manufacturer’s directions.
M
Michael JacksonSep 6, 2025
How to fix load tangling in Whirlpool WTW4850BW Washer?
- L
  Laurie AdamsSep 6, 2025
  To address load tangling in your Whirlpool Washer: * Refer to the 'Using Your Washer' section for loading recommendations. * Select a cycle with a slower wash action and spin speed; however, items will be wetter than those using a higher speed spin. See the 'Cycle Guide' to match your load with the best cycle. * Load garments in loose heaps evenly around the basket wall. * Reduce tangling by mixing types of load items. Use the recommended cycle for the type of garments being washed.
G
gjonesSep 8, 2025
Why does my Whirlpool WTW4850BW make clicking or metallic noises?
- T
  Theodore RichSep 8, 2025
  Clicking or metallic noises in your Whirlpool Washer can be due to: * Objects caught in the washer drain system. Empty pockets before washing. Loose items such as coins could fall between the basket and tub or may block the pump. It may be necessary to call for service to remove items. * Metal items on clothing, such as metal snaps, buckles, or zippers, touching against the basket. This is normal.
K
Keith BarberSep 10, 2025
Why does my Whirlpool Washer have dry spots on load after cycle?
- S
  Shannon ShafferSep 10, 2025
  Dry spots on your load after a cycle in your Whirlpool Washer are normal. The high spin speeds combined with airflow during the final spin can cause items near the top of the load to develop dry spots.

Whirlpool WTW4850BW Specifications

General

Style	top load
Color	white
Washer Capacity	3.6 cubic feet
Max Spin Speed	800 revolutions per minute
Internal Heater	no
Control Panel	electronic
Delay Start / End	no
Child Lock	no
Cycle Signal	yes
Steam	no
Annual Energy Consumption	159 kilowatt hours
Voltage	120 volts
Current	15 amperes