Why does my Whirlpool Washer take longer than the programme chart indicates?
The duration of a Whirlpool Washer programme can vary due to factors like excessive foam, unbalanced loads, or low water temperature. The washer adjusts the program duration based on the load size and these factors. For small loads, the program time may be reduced by up to 50%.
What to do if my Whirlpool WWDC 6400 says 'Water tap closed'?
If your Whirlpool Washer displays the message 'Water tap closed', it means the appliance isn't getting enough water. Here's what to check: * Ensure the water tap is fully open and the water supply pressure is adequate. * Inspect the water inlet hose for any kinks. * Check if the mesh filter of the water inlet hose is blocked. * Make sure the water hose isn't frozen. * If your appliance has a water supply hose with a safety valve inspection window, and it's red, replace the hose. After resolving the issue, restart the program by pressing 'Start(Pause)'.
Why does my Whirlpool WWDC 6400 vibrate during the spin cycle?
If your Whirlpool Washer vibrates excessively during the spin cycle, it could be due to a couple of reasons: * The transport bolts might not have been removed. Ensure these are taken out before using the appliance. * The appliance might not be level or standing firmly on all four feet. Adjust the feet to ensure it's stable.
How to fix poor final spin results in my Whirlpool WWDC 6400?
If you're experiencing poor spin results with your Whirlpool Washer, here are a few things to check: * A heavy item might be preventing proper spinning. Try adding smaller items and repeating the spin cycle. * Excessive foam could be the issue. Select and start the Rinse & Spin program and avoid using too much detergent in the future. * The spin speed might be set too low. Check the Spin button setting.
Why my Whirlpool Washer does not start even when the Start/Pause button is pressed?
If your Whirlpool Washer doesn't start even after pressing the Start/Pause button, ensure the door is properly closed. Also, check if the Child lock/Lock buttons feature is activated. If so, unlock the buttons by pushing the two buttons marked with the key symbol simultaneously for at least 3 seconds, until the key symbol disappears from the display.
What to do if my Whirlpool Washer shows the “F02” or “FA” Failure indicator?
If your Whirlpool Washer displays the “F02” or “FA” failure indicator, it indicates a Waterstop fault. Turn the program selector to the “Off/O” position, unplug the appliance, and turn off the water tap. Tilt the appliance forward carefully to allow collected water to flow out. Then, plug in the appliance again, turn the water tap on and select and start the desired program again.
What to do if my Whirlpool WWDC 6400 Washer shows the 'Clean pump' failure indicator?
If the 'Clean pump' indicator blinks on your Whirlpool Washer, it means waste water is not being pumped out. Unplug the appliance and check for the following: * Kinks or blockages in the drain hose. * Blockages in the filter or pump. * Frozen drain hose. After resolving the issue, push the 'Reset' button and restart the desired program.
What causes unbalance during spinning in Whirlpool Washers?
Unbalance during spinning in your Whirlpool Washer can occur due to small laundry loads with few large items or big/heavy laundry items. To avoid this, mix laundry items of different sizes. If you want to spin the wet laundry, add more laundry items of different sizes, and subsequently select and start the “Rinse & Spin” programme.
What to do if my Whirlpool WWDC 6400 detergent dispenser has residues?
If you notice detergent residues in the dispenser of your Whirlpool Washer, it could be due to insufficient water entering the machine. Check the mesh filters of the water supply, as they might be blocked.
Why does my Whirlpool WWDC 6400 stop during the program and the 'Start(Pause)' light flashes?
Your Whirlpool Washer might stop during a program with the 'Start(Pause)' light flashing due to several reasons: * The “Rinse hold” option may be activated. Terminate it by pressing “Start(Pause)” or selecting and starting “Drain”. * The program may have been changed. Reselect the desired program and press “Start(Pause)”. * The program may have been interrupted, and the lid opened. Close the lid and restart the program by pressing “Start(Pause)”. * The appliance’s safety system may have been activated (see “Description of failure indications”). * The water tap may not be open, or the water inlet hose may be kinked, indicated by the “Water tap closed” light.
Steps for installing the washing machine on a level surface and adjusting feet.
Requirements for safe electrical connection by a qualified technician.
Important safety guidelines for using the washing machine and for child safety.
Mandatory earthing of the washing machine for electrical safety.
Procedure for connecting wires to a rewirable plug by a qualified electrician.
Diagnosing issues when the appliance does not start or indicator lamps are off.
Troubleshooting when the appliance does not start after pressing 'Start/Pause'.
Resolving program stops and flashing 'Start/Pause' light indications.
Troubleshooting 'Water tap closed' indication and related water supply issues.
Resolving issues related to water not being pumped out and 'Clean pump' indication.
Interpreting 'bdd' (all lamps) and 'Service' indications for program sequence errors.
Troubleshooting 'F09' (Electrical module fault) and 'FA' (Waterstop fault).
General| Door hinge | Left |
|---|---|
| Cord length | 1.2 m |
| Loading type | Front-load |
| Product color | White |
| Built-in display | No |
| Appliance placement | Freestanding |
| Drum capacity | 6 kg |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Noise level (spin) | 77 dB |
| Noise level (wash) | 59 dB |
| Number of washing programs | - |
| Washing class | A |
| Annual water consumption washing | 9272 L |
| Annual energy consumption washing | 179 kWh |
| Adjustable feet | Yes |
| Current | 10 A |
| Connected load | 2300 W |
| Water consumption per cycle | 49 L |
| Energy consumption washing per cycle | 0.9 kWh |
| Package depth | 480 mm |
| Package width | 640 mm |
| Package height | 880 mm |
| Package weight | 74000 g |
Weight and Dimensions| Depth | 520 mm |
|---|---|
| Width | 595 mm |
| Height | 845 mm |
| Weight | 72000 g |
| Door opening diameter | 72000 mm |
To Next Page