Video Mode
Power Off
Photo Mode
Video Mode
Power Off
Photo Mode
AM
AM
M M
M M
PRESETS
PRESETS
FCC STATEMENT
Product Name: Digital Game Scouting Camera
Trade Name: Wildgame Innovations
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible could void the user’s
authority to operate this device. Product specifications are subject to change. Wildgame Innovations is not
responsible for any photographic or typographical errors.
IC WARNING
This device contains license-exempt transmitter(s) that comply with Innovation, Science and Economic
Development Canada’s license- exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device. This equipment meets the exemption from the routine evaluation limits in section of RSS-102. It should
be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
Product specifications are subject to change. Good Sportsman Marketing, LLC is not responsible for any
photographic or typographical errors.
May be protected by one or more U.S. Patent numbers: 6,735,387 / 6,768,868 /
6,834,162 / 7,149,422 / 7,308,196 / 7,593,632 / 7,710,457 / 8,895,926.
Battery Installation
Delay
ImageAtomic Clock Sync
Limited WarrantyFormat SD Card
Power
FCC
Time Zone
Manual Settings - Time Manual Settings - Date
Retrieving Images
(SD Card Reader)Mounting
4. 5.
3.
While the camera is switched on, if the OK button is pressed then the LCD will light up.
1.
2.
1. Slide the TIMEZONE switch to set your time zone first.
1. Slide the DELAY switch to select your delay setting. 1. Move the MODE switch to Photo or Video mode to turn the camera on.
2. When the camera is power
ed on for 3 seconds, the LCD will display the factory default
(incorrect) time. After 30 seconds, the LCD will turn off and the camera will immediately
begin capturing images.
Note: the camera’s test LED will blink on each photo/video trigger for the first 3 minutes of
operation. After that time, the test LED will remain off.
1. To change time, start by pressing and releasing the OK navigation button to set the hour.
1. Press the OK navigation button after setting the minute to change the date.
2. Press the + navigation button to go up in sequence.
3. When the hour is set , repeat steps 1 and 2 to set the minutes.
3. When the month is set , repeat steps 1 and 2 to set the day and year.
Technical Support Email:
Customerservice@gsmorg.com
Please allow 48 hours for email response.
Wildgame Innovations
P.O. Box 535189
Grand Prairie, TX 75053-9504
Customer Service
Toll Free: 877-269-8490
Call Center Hours
Mon – Fri / 8AM – 5 PM (CST)
PICTURES DISPLAY:
A- Time
B- Date
C- Moon Phase
D- Photo Count
A B C D
SDXC CARDS ARE NOT SUPPORTED
Having trouble with your SD card? Try this.
User’s Manual
IMPORTANT TIPS:
•
•
•
•
•
•
2. Press the + navigation button to go up in sequence.
1.
GSM, LLC
P.O. Box 535189
Grand Prairie, Texas 75053
Toll-free 877-269-8490
www.gsmoutdoors.com
www.wildgameinnovations.com
Open the door at the bottom of the
camera by pulling the latch.
Drop the battery tray by sliding the
orange EJECT latch to the right.
Align the batteries with the positive
(+) facing up on the outside, and the
negative (-) facing up on the inside.
IMPORTANT:
Make sure the camera is powered
off before removing or installing an
SD card.
If you are using an SD card from
other cameras, please make sure
to format the SD card in your
computer prior t
o use in your
camera. New cards are ok to use
straight from the package.
Load SD memory card (up to 32GB)
into the SD card slot with the notch
in first and the metal pins facing you.
P - On behalf of the Pacific region, the time after the camera successfully receives the RCC signal
will be reduced by 8 hours from the time set on the signal transmitter; UTC -8hr
M - On behalf of the Mountain region, the time after the camera successfully receives the RCC
signal will signal will be reduced by 7 hours from the time set on the signal transmitter; UTC -7hr
C - On behalf of the Central region, the time after the camera successfully receives the RCC signal
will signal will be reduced by 6 hours from the time set on the signal transmitter; UTC -6hr
E - On behalf of the Eastern region, the time after the camera successfully receives the RCC signal
will signal will be reduced by 5 hours from the time set on the signal transmitter; UTC -5hr
No SD card message will appear
after power up if the SD card is
missing or corrupted.
This camera can automatically acquire the time and date from the atomic
clock radio station WWVB. To initiate the sync, press and hold the + button
for 5 seconds while powering the camera on.
The camera will then attempt to sync. During this time, the test LED will
blink yellow and the LCD screen will display the word SYNC. When the
time is acquired, the test LED will blink green and the camera will briefly
display the acquired time before capturing photos/videos.
If the camera is not able to acquire the time after 10 minutes of syncing,
the LED will blink red and the LCD will display the last saved time. The
camera will attempt to sync every 6 hours, but will continue to capture
photos/videos during that time.
If the time is successfully acquired or is manually set, the camera will
attempt a sync at 1AM every day to ensure that the time is accurate. The
test LED will not light up during this sync to avoid alerting animals, but
the screen will still display SYNC .
NOTE:
Do not mix old and new batteries.
Do not mix alkaline, standard
(carbon-zinc) or rechargeable
(ni-cad, ni-mh, etc) batteries.
Press and hold the OK button for 5 seconds while turning the camera on. While the camera
is formatting the card, the LCD screen will display DLT (delete).
WARNING: formatting your SD card will delete all files placed on it .
To format your SD card using your camera
1.
2. Open (Windows) File Explorer by pressing Win + E on simultaneously your keyboard.
3. Right-click the drive letter associated with your memory device, then select “Format”
4. Ensure FAT32 is selected under “File System”
5. Ensure ”Quick Format” is checked
6. Click “Start”
1. Connect the SD card to your computer. If your computer has an SD card slot you can
insert the SD card directly into the port.
NOTE: If you are using a MicroSD card, you will need an adapter to allow it to fit into
standard SD card ports. If your computer does not have an SD card port built-in, you can
use an external USB card reader that plugs into any USB port on your computer.
To format your SD card using your computer
When mounting to a tree, first
remove the clip from one end of the
strap so you can slide the strap
through the slots located on the back
of the camera. Once the camera is
attached, place the clip back on to
the strap. Then, wr
ap the strap
around the tree and clip the two ends
together. Pull the excess material so
that the camera is strapped tightly to
the tree.
Recommended distance from target area is
25-30 feet for optimal imaging quality.
To improve the quality of your images,
try not to mount the unit facing the rising
or the setting sun in order to avoid direct
sunlight into the camera lens.
If mounting to a feeder unit or dusty
environment, be sure to clean the camera
lens cover, incandescent flash cover, and
the PIR sensor cover on a regular basis.
Periodically check the mounting of the
camera to ensure it is not loose.
Make sure that you securely latch the door
closed every time you use the camera, as
the moisture seal will not be activated
unless closed properly.
Check batteries frequently to ensure no
corrosive build-up, as this may cause harm
to the camera.
First, remove the SD Card from the camera by pressing on it until it automatically ejects.
Next, insert the SD card into your SD card reader.
Please refer to your card reader's owner's manual for the proper way of viewing the files.
You can also use the WGI SD Card Reader for Apple or Android to access and upload your
photos to the cloud using the WGI Huntsmart app on your mobile device.
1.
2.
MODEL# WGI-SWTC2LO
Delay is the time for the camera to take the next photo or video after 15 seconds,
30 seconds, or 1 minute.
SD Card Installation
Your Wildgame Innovations scouting camera is covered by a 365 Day Limited Warranty on parts and labor from
the date of original purchase, and purchases must be made through an authorized dealer. The warranty covers
defects in workmanship and materials. The warranty does not apply to units, which have been damaged or
abused intentionally or unintentionally. A purchase from individuals or unauthorized Internet sites such as
eBay voids the warranty.
This camera must be registered with Wildgame Innovations via web, email, or customer service phone
support, and accompanied with a reciept from the point of purchase, for any Factory Reset options to be
available.
Tampering with or altering the unit will void the warranty. Any unauthorized service will void warranty. A copy
of your original sales receipt must be produced for any warranty service and a Return Authorization (RA)
number must be obtained from customer service at 1.888.508.5922 prior to returning product.
Wildgame Innovations is not responsible for any lost untraceable packages or those without a Return
Authorization at the time of return.
Page 13
Page 9
Page 5
Page 1
Page 12
Page 8
Page 4
Page 14
Page 10
Page 6
Page 2
Page 11
Page 7
Page 3
To Next Page
Need help?
General
