Windsor COMDU 1.008-612.0

Questions and Answers

T
Tracy BlackwellAug 15, 2025
What to do if there is no solution flow to the floor in my Windsor COMDU 1.008-612.0?
- A
  afitzpatrickAug 15, 2025
  If you're experiencing little to no solution flow from your Windsor Floor Machine, there are several potential causes: * The solution tank might be empty, so refill it. * The solution pump might be turned off; make sure to turn it on. * The solution strainer could be plugged; clean the strainer. * There might be an obstruction in the solution system plumbing; clear any obstructions. * The pump itself could be obstructed; clean or replace it. * The solution solenoid valve might be obstructed or stuck; clean or replace the valve. * The jets could be obstructed; clean or replace the jets. * There might be a fault in the pump circuit or the pump itself; check the wiring, connections, and pump. * A faulty solenoid could also be the issue; check the solenoid valve.
Q
qbradleyAug 18, 2025
How to troubleshoot no power issue in Windsor COMDU 1.008-612.0?
- J
  justin73Aug 18, 2025
  If your Windsor Floor Machine has no power, start by checking all battery cable connections to ensure they are secure. Also, inspect the battery cables for any corrosion and clean the connections if necessary. If the issue persists, the key switch may be faulty and require replacement.
S
Stephanie ForbesAug 21, 2025
Why is my Windsor COMDU 1.008-612.0 having poor scrubbing performance?
- K
  Kiara JuarezAug 22, 2025
  If your Windsor Floor Machine's scrubbing performance is poor, start by checking the scrub brushes for any debris and remove it. Also, check the brush wear. Finally, ensure that the battery is fully charged.
B
Bruce SmithAug 26, 2025
What to do if brush motors do not run or run slowly on Windsor Floor Machine?
- T
  Travis BakerAug 26, 2025
  If the brush motors on your Windsor Floor Machine do not run or run slowly, here are a few things to check: * First, check if any circuit breakers have tripped and reset them, also check brush pressure. * Second, ensure the battery is fully charged. * Third, inspect the brush circuit or motor for faults, checking wires, connections, and the motor itself. * Lastly, examine the brush motor brushes for wear and replace them if necessary, also check the commutator.
S
Steven AndersonAug 28, 2025
Why does my Windsor COMDU 1.008-612.0 have little or no propel?
- S
  Shirley ZimmermanAug 28, 2025
  If your Windsor Floor Machine has little to no propel, consider the following potential causes: 1. Low battery charge: Charge the batteries. 2. Machine turned on with propel trigger not in neutral position: Allow pedal to return to neutral, then restart. 3. Tripped circuit breaker: Reset the circuit breaker and check the brush. 4. Controller overheated: Allow a cool down period. 5. Loose motor connection: Check wires and connections from controller to motor. 6. Faulty throttle circuit or potentiometer: Check wires and connections from throttle to controller and potentiometer resistance. 7. Faulty brake circuit: Check wires connections.
A
Alan UnderwoodAug 31, 2025
How to fix no chemical flow on Windsor Floor Machine (Deluxe)?
- C
  clawsonAug 31, 2025
  If there is no chemical flow in your Windsor Floor Machine (Deluxe model), first check if the tanks are empty and fill them, priming the chemicals. If the tanks are full, ensure the chemical pump is primed. If the issue persists, there may be a chemical system obstruction; rinse the system with water to clear it.
A
Antonio RiddleSep 4, 2025
What to do if scrub deck will not go down/up on Windsor Floor Machine?
- R
  rachelmendozaSep 4, 2025
  If the scrub deck on your Windsor Floor Machine will not go down or up, check if the actuator circuit breaker has tripped and reset it. If the problem continues, there may be a faulty actuator circuit or actuator; check the wires, connections, and the actuator itself.
J
Jessica BrooksSep 7, 2025
Why doesn't my Windsor COMDU 1.008-612.0 Floor Machine change speeds?
- D
  davidhancockSep 8, 2025
  If your Windsor Floor Machine does not change speeds, the issue might be a faulty speed control circuit or potentiometer. Check the wires, connections, and the potentiometer itself.
E
evansdanielSep 12, 2025
What causes a Windsor COMDU 1.008-612.0 Floor Machine to only have forward or reverse speed?
- M
  Miranda CookSep 12, 2025
  If your Windsor Floor Machine only operates in forward or reverse speed, the forward/reverse switch may be faulty and need replacement.