Specific Safety
Rules
DO NOT
let comfort or
familiarity
with
pillar
drill
(gained
from
repeated
use) rep
ace strict adherence to
rotary
hammer
safety
mles. if
you
use this
pillar
drii
S—“éSAEVT‘
5’9)
10.
ii.
i2.
13.
14.
15.
16.
i7.
unsafely
or
incorrectly,
you
can
suffer serious
personal
injury.
ways
wear
CE
approved
eye protection.
ways
use
sharp
drill bits
ever
use sub-standard
or blunt drill bits
ever use
excessive
force on the drill handle
ways
ensure
the
pillar
drill is
securely
mounted to
a solid
orkbench
or stand
ever remove
the
guard
ways
disconnect
the tool from
the
power
source when
setting
up. adjusting,
or
changing
accessories.
Do not wear
gloves,
scarves,
or loose
clothing.
A
ways
clamp
the
workpiece
and brace
against
column to
prevent
rotation.
Be sure the bit is secured
in
place
before
operation.
A
ways
be sure
you
have a firm
footing.
Be sure no one
is below
when
using
the
pillar
drill in
high
locations.
Keep
hands
away
from
movingparts.
Do
not leave the
pillar
drill
running.
Some
material contains
chemicals which
may
be toxic.
Take
care to
prevent
dust inhalation
and skin
contact. Follow material
supplier
safety
data.
Use
recommended
speed
for drill
accessory
and
workpiece
rotation.
Be sure drill
bit or
cutting
tools is
securely
locked
in the chuck,
Be sure chuck
key
is removed from the chuck before
connecting
to
power
source or
turningpower
ON.
>ZE>ZZ>>
19.
20.
21.
22.
23.
24.
25.
26.
27.
8.
Adjust
the table or
depth stop
to avoid
drilling
into the
able. Shut
off the
power,
remove the drill
bit.
and clean
the table before
leaving pillar
drill.
Do
not connect tool
to
power
source or
operate
until it is
completely
assembled
and installed
according
to the instructions.
fany part
of
your pillar
drill malfunctions
or has been
damaged
or
broken.
do
not
operate
until
the
part
is
properly repaired
or
replaced.
Never
place
your fingers
in a
position
where
they
could contact
the
drill or other
cutting
if the
workpiece
should
unexpectedly
shift.
Never use
your
hand to hold the
object
while
drilling.
A
ways clamp
the
object tight
on the work table
or use a drill vice
to
prevent
accidental
injury.
Do
not touch the bit
or
parts
close to the bit immediate
y
after
operation;
they may
be
extremely
hot and could
burn
skin,
clothing
etc.
Never
perform any operation
by moving
the head
unit or table with
respect
to one another. Do not turn the
switch ON or
s art
any
operation
before
checking
that the head
and table lock handles are
clamped tight
to column
and head and table
support
collars are
correctlypositioned.
Before
engaging
the
power
switch
ON,
make sure
the belt
guard
is
down and the chuck is installed
properly.
Turn the switch OFF when
leaving
the
pillar
drill. Do not
perform
layout,
assembly
or
set-up
work on the
table while the
cutting
tool
is
rotating,
switched on or connected to
a
power
source.
Firmlyclamp
or bolt
you pillar
drill to a workbench
or table.
Mount
your pillar
drill to either a workbench or
mounting
board;
iailure to
comply
could result in
possible
serious
injury.
Wolf—106302
.
Page
to
To Next Page
Loading...