To Next PageTo Next Page
What to do if my Wolf Boiler experiences flame failure during operation?
If your Wolf Boiler experiences flame failure during operation, it could be due to several reasons. Check the CO values and the flame monitor 2 and lead. Press the reset button. Inspect the flue system for leaks. Also, negative pressure at the oil pump might be too high, or flue gas recirculation might be occurring. Regular maintenance might be necessary.
What to do if my Wolf Boiler fan does not reach the set speed?
If the fan in your Wolf Boiler isn't reaching the set speed, the power cable to the fan should be checked. Also, check the fan itself. Ensure condensate can drain freely from the balanced flue system, and then press reset. Regular maintenance might be necessary.
Why does my Wolf Boiler have excess temperature (high limit safety cut-out)?
If your Wolf Boiler is experiencing excess temperature, triggering the high limit safety cut-out, it's likely because the flow temperature has exceeded 110 °C. Try testing the heating circuit pump, venting the system, pressing the reset button, and cleaning the heat exchanger.
What to do if my Wolf COB flue gas sensor shows excess temperature?
If the flue gas temperature in your Wolf Boiler exceeds 120 °C, try the following: Clean the heat exchanger and ensure all displacement devices are installed. Check the flow through the boiler and verify the boiler flow and return. Finally, press the reset button.
This operating manual applies to the COB/TS oil condensing boiler.
Refers to technical guide, installation, and service instructions for COB/TS.
System user or operator must ensure safekeeping of all instruction manuals.
Explains warning symbols used for personal safety and operational reliability.
General safety guidelines for installation, commissioning, and service of the boiler.
Warns against touching electrical components when the switch is ON, emphasizing electrocution risk.
Risk from insufficient combustion air or flue gas leaks, leading to asphyxiation.
Risk from oil-bearing parts contaminating drinking water.
Warns about hot water and precautions before working on water-contacting parts.
Warns about hot boiler components and precautions before working.
Warns about high water pressure and potential injuries.
Only qualified contractors for installation/modifications. Flue gas components must not be modified.
Avoid using specific cleaning agents or storing materials that cause corrosion.
Cleaning the casing with a damp cloth and mild agent.
Yearly inspection and maintenance by specialist workers is required.
Guidelines for use by children and persons with reduced capabilities.
Procedure for filling the heating system with water to the correct pressure.
The trap must be fitted and filled to prevent flue gas leaks.
Shut-off valves for heating flow and return must be open.
Regularly check water level and pressure gauge.
Explains the meaning of different illuminated ring states (standby, winter mode, fault).
Tips for saving energy in heating mode, including usage and servicing.
Tips for saving energy in domestic hot water (DHW) mode.
Procedure for handling fault codes and restarting the boiler.
This operating manual applies to the COB/TS oil condensing boiler.
Refers to technical guide, installation, and service instructions for COB/TS.
System user or operator must ensure safekeeping of all instruction manuals.
Explains warning symbols used for personal safety and operational reliability.
General safety guidelines for installation, commissioning, and service of the boiler.
Warns against touching electrical components when the switch is ON, emphasizing electrocution risk.
Risk from insufficient combustion air or flue gas leaks, leading to asphyxiation.
Risk from oil-bearing parts contaminating drinking water.
Warns about hot water and precautions before working on water-contacting parts.
Warns about hot boiler components and precautions before working.
Warns about high water pressure and potential injuries.
Only qualified contractors for installation/modifications. Flue gas components must not be modified.
Avoid using specific cleaning agents or storing materials that cause corrosion.
Cleaning the casing with a damp cloth and mild agent.
Yearly inspection and maintenance by specialist workers is required.
Guidelines for use by children and persons with reduced capabilities.
Procedure for filling the heating system with water to the correct pressure.
The trap must be fitted and filled to prevent flue gas leaks.
Shut-off valves for heating flow and return must be open.
Regularly check water level and pressure gauge.
Explains the meaning of different illuminated ring states (standby, winter mode, fault).
Tips for saving energy in heating mode, including usage and servicing.
Tips for saving energy in domestic hot water (DHW) mode.
Procedure for handling fault codes and restarting the boiler.
General
