9
Lithium-Ion cordless angle grinder EN
mean that you are guaranteed safety in use.
• The speed of the utilities must be at least equal
to the maximum speed specified in the device.
Accessories that move faster than their rated
speed can be broken, take out the machine and
fly.
• The outer diameter and thickness of the
accessory shall be within the capacity of the tool
for evaluation. Auxiliary accessories that are not
the right size cannot be maintained or controlled
properly.
• The size of the sucker for discs, fingers, backup
pads or any other accessories must match the
skills of the tools. Additional equipment with
sukkah holes that are incompatible with the
tool mounting platform is unbalanced, will be
excessively shaken and may cause obstruction.
• Do not use damaged accessories. Before each
use, check accessories such as grinding discs
and make sure there are no chips or cracks,
check the support pads for excessive cracks,
tears, or grinding, and make sure that the wire
brush does not contain loose or cracked wires.
If the tools or utilities fell, check that they are
not damaged and that no additional extensions
are installed. After checking and attaching
the accessory, keep yourself and spectators
away from the accessory rotary plane and run
the tool at full speed, without loading, for one
minute. Auxiliary accessories that are normally
damaged will be broken during test time.
• Assembling of personal protective equipment.
Depending on use, use a face shield, safety
glasses, or safety mask. As required, place a
dust mask, earmuffs, gloves, and a workshop
gown capable of keeping small rough particles.
Eye protection equipment should be able to stop
flying debris left by various operations. The dust
mask or ventilator should be able to filter out the
particles produced by your actions. Prolonged
exposure to high-intensity noise can cause
hearing loss.
• Keep pedestrians at a safe distance from the
work area. Every person entering the work area
must wear personal safety equipment. Cutting
off the work piece or broken accessories may
fly and cause injury outside the immediate work
area.
• Hold the tool only with an insulated coating grip
during the procedure as the accessory may be
in contact with the characteristic wires or its
power cord. The following cutting accessory
that comes in contact with the “direct” power
cord may cause the metal parts of the power
tools to expose the user to power.
• Place the power cord away from the rotary
accessory. If you lose control of the tools, the
cable may be cut or torn and your arm may
extend to the rotating accessory.
• Never place the tools before the accessory
stops completely. The rotary accessory may
attach to the surface and remove the tool from
your control.
• Do not operate the tool while holding it next to
the body. Accidental contact with the revolving
accessory can cause a fit in your clothes and
thus pull the tools towards your body.
• Clean the tool air vents regularly. The engine
fan pulls dust into the machine casing and
excessive accumulation of metallic powder
increases the risk of electric shock.
• Do not operate tools near flammable materials.
Sparks can light these materials.
• Do not use any accessories that require coolant.
Using water or other refrigerants can cause
electric shock or shock.
PAGE AND ASSOCIATED
WARNINGS:
• The page is a sudden response to the
turntable, backup platforms, requests, or any
other extension that is installed or detected.
Pressure or grip causes a sudden stop of the
rotary attachment, which in turn causes the
fully uncontrolled tools to push strongly in the
opposite direction to rotate the attachment at
the attachment point. For example, if a hard disk
is detected or installed in the workbench, the
edge of the disc that enters the disc point can be
etched into the surface of the material, causing
the disc to climb or push out. The disc may
jump in the direction or away from the player,
depending on the direction of movement of the
disc at the point of the disc. Rough disks may
also break under these conditions.
The disadvantage is the result of improper use
of tools and or incorrect processes or operating
conditions and can be prevented by taking the
above precautions.
• Never place your hands near the rotary
accessory. The additional accessory may help to
move around.
• Keep your body away from the area where
the tool will move if page movement occurs.
The column will rotate the tool in the opposite
direction to the disk position at the perception
point.
• Use extreme caution when working on sharp
corners, edges, and the like. Avoid jumping or
grabbing accessories. Angles, sharp edges, or
pop-ups tend to grab the rotary accessory and
cause loss of control or thrust.
• Do not connect a saw chain with a questionable
piece of wood or sawn. These codes often
generate the page and result in loss of control of
the tool.
To Next Page
Loading...
