Yaesu FTM-300DE Information For Customers Operating

1. Turn the transceiver ON.
2. Press the
[
BAND
(
SQL
)]
key to enter the 144 MHz band.
3. Press and hold the
[
MHz
(
SETUP
)]
key.
4. Rotate the DIAL knob to select “OPEN MSG 28” and
then press the
[
MHz
(
SETUP
)]
key.
5. Rotate the DIAL knob to select “MESSAGE” and then
press the
[
V/M
(
MW
)]
key.
6. Enter “AH075M”.
1) Rotate the DIAL knob to select “A”, then press the
[
V/
M
(
MW
)]
key.
2) Repeat the previous step to complete the MESSAGE
“AH075M”.
3) Press and hold the
[
MHz
(
SETUP
)]
key.
Information for Customers Operating VHF/UHF Transceivers in the UK
Thank you very much for purchasing the YAESU transceiver.
The transceivers listed in this notice are congured at the factory with the ARS (Automatic Repeater Shift) Frequency
Range, and the Repeater shifts, as shown in the below chart “”.
When any of the listed transceivers is operated in a location where the frequency range and repeater shifts in use are
as shown in the chart “”; follow the respective procedure to change the Automatic Repeater
Shift conguration, before using the transceiver for the rst time.

Factory Default Setting

Selectable Setting
ARS Frequency Range: 438.20 MHz - less than 439.45 MHz
(
- shift
)
Repeater Shifts: 7.6 MHz
ARS Frequency Range: 433.00 MHz - less than 433.40 MHz
(
+ shift
)
434.60 MHz - less than 435.00 MHz
(
- shift
)
Repeater Shifts: 1.6 MHz
Caution:
• BychangingtheARSdesignatedbandsandrepeatershiftsaccordingtotheproceduresbelow,allsaveddata,suchas
MenuandMemorysettings,willbedeleted.IfyouneedtochangetheARSfeaturesettingafterusingtheradio,make
suretobackupyourregistereddataormakeawrittennote,beforeapplyingthesettingchange.
• TheARSfeaturesettingisNOTchanged,evenwhenexecutingthe“FactoryReset”torestorethetransceivertothe
factorydefaults,asdescribedintheOperatingManuals.
7. Turn the transceiver OFF.
8. Press and hold the
[
BAND
(
SQL
)], [
GM
(
AMS
)]
and
[
MODE
(
DG-ID
)]
keys while turning the transceiver ON.
9. <TYPE B2> appears in the display.
10. Rotate the DIAL knob to select <TYPE C2> and press
the
[
GM
(
AMS
)]
key. The transceiver will re-start auto-
matically. Setting of the
ARS feature to “Cong-
uration C2” is success-
fully completed.
TorestoretheARSfeaturesettingtothefactorydefault
(
B2
)
,
performthesameproceduresabove.


1. Turn the transceiver OFF.
2. Connect the supplied microphone SSM-85D to the trans-
ceiver.
3. Press and hold the
[
F
(
SETUP
)]
and
[
GM
]
keys while turn-
ing the transceiver ON.
4. Press the
[
Power
]
key briey, then “LOCK” will appear on
the display for one sec.
5. Press
[
8
]
à
[
9
]
à
[
7
]
à
[
7
]
à
[
3
]
à
[

]
keys on the SSM-
85D microphone.
6. <TYPE B2> appears in the display.
7. Press the
[
Power
]
key briefly, then “UN LOCK” will ap-
pear on the display for one sec.
8. Rotate the DIAL knob to se-
lect <TYPE C2> and press
and hold the DIAL knob. The
radio will re-start automatical-
ly. Setting of the ARS feature
to “Configuration C2” is suc-
cessfully completed.
TorestoretheARSfeaturesettingtothefactorydefault
(
B2
)
,
performthesameproceduresabove.

1. Turn the transceiver OFF.
2. Connect the supplied microphone MH-48A6JA to the
transceiver.
3. Press and hold the
[
F
(
MW
)]
and
[
GM
]
keys while turning
the transceiver ON.
4. Press the
[
Power
]
key briey, then “LOCK” will appear on
the display for one sec.
5. Press
[
8
]
à
[
3
]
à
[
7
]
à
[
8
]
à
[
3
]
à
[
7
]
keys on the MH-
48A6JA microphone.
6. Press the
[
Power
]
key briey, then “UNLOCK” will appear
on the display for one sec.
7. Press and hold the
[
DISP
(
SETUP
)]
key.
8. Touch the
[
RESET/CLONE
]
on the display.
9. The ARS Configuration
name “B2” will appear in the
top right of the display.
10. Press
[
F
(
MW
)]
key, then the
message <Confirming FROM
“B2” TO “C2”> will appear on
the display.
BACK
BACK
RESET/CLONE




FACTORY RESET
PRESET
RECALL PRESET
MEM CH RESET
〉
〉
〉
〉
VERSION
MAIN :x.xxx 0EXP B2
PANEL:x.xx
11. Touch
[
OK?
]
. The radio will re-start automatically. Set-
ting of the ARS feature to “Conguration C2” is success-
fully completed.
TorestoretheARSfeaturesettingtothefactorydefault
(
B2
)
,
performthesameproceduresabove.

Yaesu FTM-300DE Specifications

General

Brand	Yaesu
Model	FTM-300DE
Category	Transceiver
Language	English