Yakima ForkChop User Manual

Instruction #1035813C-1/9
ForkChop
12 mm x 100 mm
15 mm x 100 mm
15 mm x 110 mm
15 mm x 150 mm
BEBQUFSTtBEBQUBUFVSTtBEBQUBEPSFT
MPDLJOH23TLFXFSY
BYFWFSSPVJMMBCMFY
CSPRVFUB23EFCMPRVFPY
XIFFMUSBZY
TVQQPSUEFSPVFY
TPQPSUFEFSVFEBY
SPVOECBSBEBQUFSY
BEBQUBUFVSQPVSCBSSFSPOEFY
BEBQUBEPSQBSBCBSSBSFEPOEBY
NFEJVNTUSBQY
TBOHMFNPZFOOFY
DPSSFBNFEJBOBY
MPOHTUSBQY
TBOHMFMPOHVFY
DPSSFBMBSHBY
IFBEVOJUY
TVQQPSUEFGPVSDIFY
VOJEBEQSJODJQBMY
NNBEBQUFSTY
BEBQUBUFVSTøNNY
BEBQUBEPSFTEFNNY
$POUFOUTt$POUFOVt$POUFOJEP
32”(81 cm) mín. - 50”(127 cm) máx.
$SPTTCBS4QSFBEt+FVEFTCBSSFTUSBOTWFSTBMFTt4FQBSBDJØOFOUSFMBTCBSSBT
.BY#JLF8FJHIUt1PJETNBYJNVNEVWÏMPt1FTPNÈYJNPEFMBCJDJDMFUB
40lbs / 18.1kg
=
-10”
32” (81 cm)
bike wheelbase
l'empattement du vélo
la distancia entre los ejes de la bicicleta
minimum
le minimum
mínimo
+10”
Crossbar spread must be ±10” of your bike wheelbase for proper use.
La distance entre les barres transversales doit être
de +/- 25 cm identique à l'empattement du vélo.
Para un uso apropiado, la separación entre las barras transversales
debe ser igual +/-10" de la distancia entre los ejes de la bicicleta.
+ 25 cm - 25 cm
Some crossbars
cannot be adjusted.
Follow instructions for
your roof rack system.
Certaines barres
transversales ne peuvent pas
être ajustées. Suivre les
instructions accompagnant
le porte-bagage.
Ciertas barras transversales
no se pueden ajustar. Siga
las instrucciones para su
sistema de barras para techo.
#8007202
2-Pack SKS Locks
Serrures SKS (x 2)
Kit doble de cerraduras SKS
#8002120
FatBike QR Locking Skewer
Axe verrouillable pour vélo à
pneus surdimensionnés
Broqueta QR de bloqueo FatBike
"WBJMBCMFBDDFTTPSJFTt"DDFTTPJSFTEJTQPOJCMFTt"DDFTPSJPTEJTQPOJCMFT

Yakima ForkChop Specifications

General

Weight Capacity	40 lbs
Material	Steel
Minimum Wheel Size	20"
Maximum Wheel Size	29 inches
Maximum Tire Width	3 inches
Type	Fork-mounted bike rack

Summary

ForkChop Installation Steps

Prepare Head Unit and Mount to Crossbar

Prepare the head unit, select the crossbar slot, and mount it securely.

Select Bike Axle Adapter

Determine and select the appropriate adapter for your specific bike axle type.

Secure Head Unit and Test Installation

Close the head unit cover, test the installation, and retighten if necessary.

Install Wheel Strap and Tray

Install the wheel strap and then place and tighten the wheel tray.

Loading and Securing Your Bike

Load Bike Onto Carrier

Set bicycle forks vertically onto the skewer and ensure they are fully seated.

Secure Bike with Skewer

Tighten the adjustment knob until the lever closes with firm resistance.

Bike Removal and Maintenance

Unload and Remove Bike

Release the wheel strap and skewer to carefully lift the bike off.

Carrier Removal and Storage

Loosen knobs, remove the unit and wheel tray, and store the carrier safely.

Maintenance and Cleaning

Use non-water soluble lubricant on screws and clean plastic parts with a soft cloth.

Load Limits and Safety Checks

Check Load Limits

Verify the weight limit online and do not exceed the specified maximum load.

Reinstallation and Safety

Follow instructions for reinstallation and perform safety checks after every installation.

Important Warnings and Precautions

Safety Tab and Installation Warnings

Ensure safety tabs are present; improper installation can cause damage or injury.

Bike and Fork Compatibility

Do not modify bike dropouts or use incompatible forks; check compatibility before use.