Yale UNI Series User Manual

Page 2
Non-Holder
Hold-Open
inches
mm
Hold
Open
Door Stop
inches mm inches mm inches mm inches mm inches mm inches mm inches mm
85° 90° 9-7/8 251 9-7/8 251 10 254 10 254 10-1/8 257 10-1/4 260 10-1/4 260
90° 95° 9-1/4 235 9-1/4 235 9-3/8 238 9-3/8 238 9-1/2 241 9-5/8 244 9-5/8 244
95° 100° 8-5/8 219 8-5/8 219 8-3/4 222 8-3/4 222 8-7/8 225 9 229 9 229
100° 105° 8-1/8 206 8-1/8 206 8-1/4 210 8-1/4 210 8-3/8 213 8-1/2 216 8-1/2 216
105° 110° 7-5/8 194 7-5/8 194 7-7/8 200 7-7/8 200 8 203 8-1/8 206 8-1/8 206
110° 115° 7-1/4 184 7-1/4 184 7-1/2 191 7-1/2 191 7-3/4 197 7-7/8 200 7-7/8 200
Non-Holder
Hold-Open
inches
mm
Hold
Open
Door Stop
inches mm inches mm inches mm inches mm inches mm inches mm inches mm
85° 90° 10-1/4 260 10-3/8 264 10-3/8 264 10-1/2 264 10-5/8 270 10-3/4 273 10-3/4 273
90° 95° 9-1/2 241 9-3/4 246 9-3/4 246 9-7/8 251 10 254 10-1/8 257 10-1/8 257
95° 100° 9 229 9-1/8 232 9-1/4 235 9-1/4 235 9-3/8 238 9-1/2 241 9-1/2 241
100° 105° 8-3/8 213 8-1/2 216 8-3/4 222 8-3/4 222 9 229 9-1/8 232 9-1/8 232
105° 110° 8 203 8-1/8 206 8-1/4 210 8-3/8 213 8-5/8 219 8-3/4 222 8-3/4 222
110° 115° 7-1/2 191 7-3/4 197 7-7/8 200 8 203 8-1/4 210 8-3/8 213 8-3/8 213
Door-C ontrol location f or 1-3/4" (44mm) thick doors hung on
4-1/2" (114mm) wide template-hinges or 3/4" (19mm) off set-pivots.
Figure 2
Arm
Number
Stamp
J6600-4
J6600-7
J6200-4
J6200-7
J6100-4
J6100-7
J6400-4
J6400-7
0-3/8
0-10
2-1/2 - 3-1/4
55 - 83
Dimension A
1/2 - 2
13 - 50
Dimension A Dimension A
3-3/8 - 4-1/4
85 - 108
Dimension A
5-1/2 - 6-3/8
140 - 162
Dimension A
J6500-41
J6500-71
4-3/8 - 5-3/8
111 - 137
Dimension A
Reveal
Door Opening Angle
J6500-43
J6500-73
6-1/2 - 7-3/8
165 - 187
Dimension A
J6400-42
J6400-72
Figure 3
Arm
Number
Stamp
J6600-4 J6200-4 J6100-4 J6400-4 J6500-41 J6400-42 J6500-43
J6600-7 J6200-7 J6100-7 J6400-7 J6500-71 J6400-72 J6500-73
2-1/2 - 3-1/4
0 - 10 13 - 50 55 - 83 165 - 187
3-3/8 - 4-1/4 4-3/8 - 5-3/8 5-1/2 - 6-3/8 6-1/2 - 7-3/8
Dimension ADoor Opening Angle Dimension A Dimension A Dimension A
Door-C ontrol location f or 1-3/4" (44mm) thick doors hung on center pivots.
Dimension A Dimension A Dimension A
85 - 108 111 - 137 140 - 162
Reveal
0-3/8 1/2-2
Figure 1
80-9303-2214-010 (07-08)
Top-Jamb Installation Template
Do Not Scale Drawing
Left Hand Door Shown
Dimensions are in
C
L
Hinge or Pivot
12
(304.8)
3-1/4
(82.6)
4-1/8
(104.8)
inches
(mm)
1/2
(13)
Hinge Edge of Door
3/4
(19.1)
Reveal
C
L
Closer Pinion
A
3
(76)
Without Drop Plate *
With Drop Plate *
* Always use frame or transom rabbet as
reference plane, not bottom of stop.
** For 1-3/4” door with 4-1/2” wide butts or 3/4”
offset-pivots, see Figure 2.
For 1-3/4” door with center-pivots, see Figure 3.
All other conditions require special template.
Frame Rabbet
1-1/8
(29)
5/16
(8)
1
(25)
4
(102)
4
(102)
Frame Stop
4 Holes For Drop Plate
Application Only

Yale UNI Series Specifications

General

Brand	Yale
Model	UNI Series
Category	Door Opening System
Language	English