What to do if Yamaha Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
How to fix Yamaha Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha 55BED S-transom Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
What to do if Yamaha 55BED S-transom gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
What causes Yamaha Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
How to fix Yamaha Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
What to do if the Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
General| Brand | Yamaha |
|---|---|
| Model | 55BED S-transom |
| Category | Outboard Motor |
| Language | English |
Defines WARNING for hazardous situations and NOTICE for precautions to avoid damage.
Details the steps for safely removing the outboard motor from its steel crate.
Provides instructions on how to properly mount the outboard motor onto the boat transom.
Provides WOT RPM ranges for selecting appropriate propellers for different engine models.
Details various types of Yamaha remote controls and their applications.
Introduces the multi-function tiller handle and its electrical functions.
Provides instructions for mounting gauges, including analog gauge illumination.
Covers speedometer types, applications, dimensions, and tube routing.
Describes the functions and applications of the fuel management gauge.
Details the setup procedure for the fuel management gauge, including switch settings and compensation.
Explains analog trim meter applications, dimensions, and adjustment procedures.
Covers coolant pressure meter applications, additional parts, dimensions, and installation.
Details coolant temperature meter applications, additional parts, dimensions, and sensor installation.
Provides wiring diagram samples for various configurations.
Summarizes the functions of digital network gauges for various engine models.
Lists engine models compatible with the digital network premium gauge.
Shows wiring for single engine applications with 6Y9 gauges and 6X6 binnacle mount controls.
Illustrates wiring for single engine applications with 6Y8 gauges and 6X6 binnacle mount controls.
Details wiring for single engine applications with 6Y9 gauges and 6X7 concealed controls.
Shows wiring for single engine applications with 6Y8 gauges and 6X7 concealed controls.
Provides wiring diagrams for twin engine applications with 6Y9 gauges.
Illustrates wiring diagrams for twin engine applications with 6Y8 gauges.
Details wiring diagrams for triple engine applications with 6Y9 gauges.
Shows wiring diagrams for triple engine applications with 6Y8 gauges.
Wiring diagrams for dual station single engine applications with 6Y9 gauges.
Illustrates wiring diagrams for dual station single engine applications with 6Y8 gauges.
Wiring diagrams for dual station quad engine applications with 6Y9 gauges.
Provides guidance on selecting appropriate batteries based on engine model and capacity.
To Next Page
