What to do if Yamaha 55BET 55DEHD E60HMHD Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
What to do if the Yamaha 55BET 55DEHD E60HMHD Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha 55BET 55DEHD E60HMHD illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha 55BET 55DEHD E60HMHD Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha 55BET 55DEHD E60HMHD Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha Outboard Motor gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha 55BET 55DEHD E60HMHD Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
How to fix Yamaha 55BET 55DEHD E60HMHD trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
What causes Yamaha 55BET 55DEHD E60HMHD gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
General| Brand | Yamaha |
|---|---|
| Model | 55BET 55DEHD E60HMHD |
| Category | Outboard Motor |
| Language | English |
Instructions to avoid severe injury or death.
Precautions to avoid damage to the product.
Step-by-step guide for safely uncrating the outboard motor from its steel frame.
Procedures for correctly mounting the outboard motor onto the boat transom.
Guidance on selecting the correct propeller pitch for varying load conditions and engine speeds.
Describes the electrical functions and components of the 6x4 multi-function tiller handle.
Covers fuel management gauge functions, applications, dimensions, and setup procedures.
Wiring diagrams for single, twin, and triple engine setups with digital network gauges.
Steps for initial setup of digital network gauges, especially for multi-engine installations.
Common troubleshooting tips for issues with digital network gauges and system setup.
Table listing suitable batteries based on model, unit, and minimum rating (CCA, MCA, RC, etc.).
Wiring instructions for isolator-equipped models and twin-battery configurations.
Checklist for static and dynamic checks to ensure customer satisfaction before delivery.
To Next Page
