What to do if my Yamaha AX-596 Amplifier cannot be turned on?
If your Yamaha Amplifier won't turn on, check the following: * Ensure the power cord is fully plugged in. Firmly plug in the power cord. * Make sure the IMPEDANCE SELECTOR switch on the rear panel is set to either end. If it's not, set the switch to either end when the unit is off.
What to do if Yamaha Amplifier remote control does not work?
If the remote control for your Yamaha Amplifier isn't working, try these solutions: * Replace the batteries with new ones if they are weak. * Ensure you are within the remote control's functional range (maximum 6 meters) and within 30 degrees off-axis from the front panel. * Reposition the main unit if direct sunlight or lighting is striking the remote control sensor.
Why does my Yamaha AX-596 Amplifier have no sound?
If your Yamaha Amplifier is producing no sound, there could be several reasons: * The output cords might be incorrectly connected. Ensure that the cords are properly connected. If the problem continues, the cords may be defective. * The appropriate input source might not be selected. Use the INPUT selector to choose the correct source. * The SPEAKERS switches might not be set correctly. Make sure the corresponding SPEAKERS switch is in the ON position. * The speaker connections might not be secure. Check and secure all connections.
What to do if my Yamaha AX-596 Amplifier sound suddenly goes off?
If the sound from your Yamaha Amplifier suddenly cuts out, the protection circuit may have been activated due to a short circuit or other issue. Turn off the unit by pressing the POWER switch, and then turn it back on to reset the protection circuit.
Why is there a lack of bass and no ambience on my Yamaha AX-596 Amplifier?
If you're experiencing a lack of bass and ambience with your Yamaha Amplifier, it's possible that the + and – wires are connected in reverse at the amplifier or speakers. Ensure you connect the speaker wires in the correct phase (+ and –).
What to do if Yamaha AX-596 does not work normally?
If your Yamaha Amplifier is not working normally, it may be due to strong external noise (lightning, excessive static electricity, etc.) or a misoperation. Turn off the unit by pressing the POWER switch. After about 30 seconds, turn it back on and try operating it again.
Why is the sound degraded when listening with headphones on my Yamaha Amplifier?
If the sound quality is degraded when using headphones connected to a compact disc player or tape deck with your Yamaha Amplifier, ensure that the unit is turned on. If it's off or in standby mode, turn on the power to the unit.
Why is the sound 'humming' on my Yamaha Amplifier?
If your Yamaha Amplifier is producing a humming sound, consider these potential causes: * Incorrect cord connections: Firmly connect the audio plugs. If the problem persists, the cords may be defective. * No connection from the turntable to the GND terminal: Make the GND connection between the turntable and the unit.
What to do if only one speaker produces sound on my Yamaha AX-596 Amplifier?
If only one speaker is working with your Yamaha Amplifier, check these: * Incorrect setting of the BALANCE control: Adjust the BALANCE control to the appropriate position. * Incorrect cord connections: Connect the cords properly. If the problem continues, the cords may be defective.
Why is the volume level low while playing a record on my Yamaha Amplifier?
If the volume level is low when playing a record on your Yamaha Amplifier, it might be because the record is being played on a turntable with an MC cartridge. In this case, the turntable should be connected to the unit through the MC head amplifier.
General| Signal to Noise Ratio | 110 dB (CD) |
|---|---|
| Dimensions | 435 x 151 x 387 mm |
| Damping Factor | 240 (8 ohms, 1kHz) |
| Input Sensitivity | 150mV (line) |
| Output | Rec Out |
| Speaker Load Impedance | 4 ohms to 16 ohms |
| Frequency Response | 5Hz-100kHz (+0/-3dB) |
| Total Harmonic Distortion | 0.015% (8 ohms, 20Hz-20kHz) |
To Next Page
