To Next PageTo Next PageHow to improve noise at track changes on Yamaha CDR-HD1300?
If a noise occurs at the change of tracks recorded from an analog record and edited, it's likely due to a very low frequency component among the wow and flutter of the analog record being output as noise. You can improve this by adding a short fade-in or fade-out to the track.
What to do if Yamaha CDR-HD1300 Recording Equipment does not turn on?
If your Yamaha Recording Equipment does not turn on when you press the power button, ensure that the power cable is securely connected.
What to do if Yamaha CDR-HD1300 Recording Equipment sound skips?
If the sound skips, it might be due to vibration or impact affecting the unit or connected components. Try relocating the unit. Also, check if the CD is dirty and clean it if necessary. Note that if the skipping sound is already on the recording due to vibrations or impact that occurred during recording, relocating the unit will not help.
What to do if Yamaha CDR-HD1300 Recording Equipment does not operate properly?
If your Yamaha Recording Equipment is not operating properly, the internal microcomputer may have frozen. Turn off the power and then turn it back on after about one minute.
How to fix vibration noise during Yamaha CDR-HD1300 copying?
Vibration and rotation noise during copying occur because the unit copies by rotating the CD, CD-R, or CD-RW disc at high speed. To reduce this noise, lower the copying speed.
What to do if recording or copying is not possible on Yamaha CDR-HD1300?
If recording or copying is not possible, consider the following: * Ensure you are using a recordable CD that has not been finalized yet. * Verify that the INPUT is correctly set according to the input signal. * If digitally copying sources, switch to ANALOG to make a recording. * Check if there is enough available space on the disc or HDD. If not, load a recordable disc or erase unused space on the HDD. * If the power was interrupted during recording of a CD-RW disc, try recording again from the beginning. When the recording of a CD-R disc is interrupted, start recording over again with a disc that can be recorded on. * Clean or replace the CD-R or CD-RW disc if it is dirty or damaged. * Ensure the HDD is installed properly.
What to do if Yamaha CDR-HD1300 Recording Equipment HDD cannot be selected?
If the HDD cannot be selected, ensure that the HDD is installed properly following the attached instructions. Also, if the HDD is newly installed, format it on the CDR-HD1300 you plan to use it with.
What causes impaired picture on TV with Yamaha Recording Equipment?
If the picture on the TV is impaired, and you are using an indoor antenna, try using an outdoor antenna or setting the unit away from the TV set.
Why can't a CD-R or CD-RW recorded with Yamaha CDR-HD1300 Recording Equipment be played on other players?
A CD-R or CD-RW disc recorded with this unit may not play on other CD or DVD players if those players are not compatible with CD-R or CD-RW discs. Also, the CD-R or CD-RW disc may need to be finalized.
What to do if Yamaha CDR-HD1300 TV does not correctly function?
If the TV does not function correctly when using the remote control, the remote control might be interfering with the TV's remote control sensor. Try relocating the unit away from the TV or cover the TV’s remote control sensor.
General| Brand | Yamaha |
|---|---|
| Model | CDR-HD1300 |
| Category | Recording Equipment |
| Language | English |
Explains digital recording rules, including SCMS.
Details system limitations, sampling rates, and signal types.
Procedure to copy all tracks from a CD to the HDD.
Method for selecting and copying specific favorite tracks from a CD to the HDD.
Steps to record audio from digital sources like TV tuners or DVD players.
Steps to record audio from analog sources like cassette decks or turntables.
Procedure for setting up timer recordings from external sources.
Detailed steps for configuring timer-based recording operations.
How to set optimal recording levels for both digital and analog inputs.
How to configure parameters for synchronized recording modes.
Operations for managing and editing albums on the HDD.
Operations for managing and editing individual tracks on the HDD.
Operations for managing and editing discs on the HDD.
Overview of how to create and edit albums stored on the HDD.
Steps to create a new album by selecting tracks.
Procedure to copy discs, albums, or bookmarks to a new album.
How to adjust the sound level of individual tracks within an album.
How to adjust the time interval between tracks in an album.
How to add or delete tracks from existing albums.
How to change the order of tracks within an album.
Overview of the operations available for editing tracks on the HDD.
How to change the track number or order of tracks.
How to change the start point of a track earlier or later.
Procedure to remove a selected track from the HDD.
How to erase a specific portion of a track.
How to merge consecutive tracks into a single track.
Overview of operations for managing and editing discs on the HDD.
Steps to copy entire discs, albums, or bookmarks from HDD to CD.
Method to copy specific favorite tracks from HDD to CD.
Using AMQR mode for high-fidelity CD copies.
Using AMQR mode for high-fidelity CD duplication.
Procedure for playing audio from a CD.
Steps to play back audio files stored on the HDD.
Steps to resolve issues when the unit fails to power on.
General troubleshooting for unit malfunction or freezing.
Identifies causes and remedies for failed recording or copying.
Troubleshooting steps for a non-functional remote control.
Lists the necessary interface, size, and capacity for compatible HDDs.
Completes the physical installation steps for the HDD.
Step-by-step guide for physically installing the HDD into the unit.
Procedure to format a newly installed HDD for use with the unit.
