Why doesn't my Yamaha E40JMH Outboard Motor boat speed gauge show?
If the boat speed and/or coolant pressure gauge isn't showing, it means the optional sensor hasn't been installed. Install the optional sensor to fix this.
What to do if the Yamaha E40JMH Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha E40JMH fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
Why does my Yamaha E40JMH fuel management gauge show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting is probably wrong. Fill the tank with fuel, and then set the correct fuel tank capacity.
What to do if my Yamaha Outboard Motor speedometer shows the incorrect fuel level?
If the speedometer shows an incorrect fuel level, the fuel sensor selection is likely wrong. You should set up the fuel sensor to the correct resistance.
What does it mean when my Yamaha Outboard Motor gauge shows “----”?
If the gauge shows “----”, it indicates that the digital signal is not being received. Make sure the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha E40JMH boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What causes Yamaha E40JMH Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Step-by-step guide for safely uncrating the outboard motor from a steel frame.
Instructions on how to properly mount the outboard motor on the boat transom for optimal performance.
Table showing recommended engine RPM ranges at Wide-Open-Throttle for selecting the correct propeller.
Overview of the multi-function tiller handle and its electrical functions.
Procedure for initial setup of digital network gauges when multiple engines are installed.
A table listing common symptoms, causes, and suggested measures for troubleshooting gauge issues.
Illustrates wiring diagrams for single station digital network premium gauges.
Provides battery specifications (CCA, MCA, RC) based on engine model and charging voltage.
Illustrates battery wiring for single and twin engine applications, including isolator usage.
Checklist for pre-delivery inspection to ensure customer satisfaction before operation.
Step-by-step guide for safely uncrating the outboard motor from a steel frame.
Instructions on how to properly mount the outboard motor on the boat transom for optimal performance.
Table showing recommended engine RPM ranges at Wide-Open-Throttle for selecting the correct propeller.
Overview of the multi-function tiller handle and its electrical functions.
Procedure for initial setup of digital network gauges when multiple engines are installed.
A table listing common symptoms, causes, and suggested measures for troubleshooting gauge issues.
Illustrates wiring diagrams for single station digital network premium gauges.
Provides battery specifications (CCA, MCA, RC) based on engine model and charging voltage.
Illustrates battery wiring for single and twin engine applications, including isolator usage.
Checklist for pre-delivery inspection to ensure customer satisfaction before operation.
General| Engine Type | 2-Stroke |
|---|---|
| Horsepower | 40 hp |
| Fuel Induction System | Carburetor |
| Ignition System | CDI |
| Starting System | Manual |
| Trim Method | Manual |
| Recommended Fuel | Regular Unleaded Gasoline |
| Fuel Type | Gasoline |
| Gear Ratio | 2.0:1 |
| Steering | Tiller |
| Full Throttle Operating Range | 5000 - 5500 rpm |
| Gear Shift | Forward, Neutral, Reverse |
To Next Page
