What to do if no sound is produced from my Yamaha Electone EL-37 Musical Instrument speakers?
If no sound comes from your Yamaha Musical Instrument speakers, the issue might be a disconnected cable plug from the speaker unit. Refer to the “Assembly Instructions” and ensure the plug is securely reconnected.
What to do if the sound is too soft on my Yamaha Musical Instrument despite maximum volume?
If the sound from your Yamaha Musical Instrument is too soft even at maximum volume, check all volume controls. Ensure the panel volume controls for each voice section, the Master Volume dial, and the Expression Pedal are set to appropriate levels.
What to do if my Yamaha Musical Instrument panel doesn't function normally?
If your Yamaha Musical Instrument panel malfunctions or memorized data changes, power surges or spikes could be the cause. Perform a Power On Reset operation to reset the instrument. (See page 47.)
Why does my Yamaha Electone EL-37 make a cracking noise?
A cracking noise from your Yamaha Musical Instrument may occur when an electrical appliance is turned on or off, or an electric power tool is used nearby. Try plugging the instrument into an electrical outlet farther from the device causing the interference.
What to do if recording stops before the performance is finished on my Yamaha Electone EL-37 Musical Instrument?
If recording stops prematurely or the Song Copy function fails on your Yamaha Musical Instrument, it could be due to the disk's storage limit being reached. Use another disk or delete unnecessary song data. (See page 64.)
What to do if notes are stuck during playback on my Yamaha Electone EL-37?
If notes are stuck during playback on your Yamaha Musical Instrument, it might be because the disk was removed using the EJECT button. Always press the STOP button to halt playback.
Why does switching voices change the volume on my Yamaha Electone EL-37?
If switching voices changes the volume on your Yamaha Musical Instrument, even with identical volume settings, some voices may sound quieter than others. Adjust the sound balance using the Volume control within the appropriate Voice Condition display.
Why do pedal voices not sound on my Yamaha Musical Instrument?
If the pedal voices on your Yamaha Musical Instrument aren't sounding despite correct volume settings, the Single Finger or Fingered Chord mode of Auto Bass Chord may be active. Turn off this mode in the display. (See page 36.)
Why can't I record 40 songs on my Yamaha Electone EL-37 Musical Instrument?
If you cannot record 40 songs on your Yamaha Musical Instrument, it may be because some song numbers contain a large amount of recorded data, and the disk may not have enough available memory left.
What to do if the accompaniment cannot be heard on my Yamaha Musical Instrument?
If the accompaniment on your Yamaha Musical Instrument is inaudible despite a suitable volume level, ensure that the rhythm has been started. The accompaniment should be used together with the rhythm.
General| Brand | Yamaha |
|---|---|
| Model | Electone EL-37 |
| Category | Musical Instrument |
| Language | English |
Explains safety symbols and provides cautions for safe operation.
Addresses environmental friendliness, battery info, and disposal guidelines.
Clarifies service responsibility, name plate location, and general important notices.
Disclaimer stating that specifications may be modified without prior notice.
Highlights AWM tone generation and digital effects like Tremolo, Reverb, Flanger, Delay.
Details dynamic rhythm patterns, automatic accompaniment, and programming features.
Explains instant setting changes via Registration Menus and digital performance recording.
Covers initial setup steps: plugging in the power and turning on the Electone.
Basic operations for playing, including volume and expression pedal use.
Explains basic registrations, menu disks, and how to use the LCD display.
Step-by-step guide to selecting voices using panel buttons and data controls.
Covers using dotted buttons and user voices for expanded voice selection.
Lists available voices and their assignments to panel buttons and pages.
Adjusting voice parameters like touch, volume, and octave via condition pages.
Details effects such as Tremolo, Symphonic, Delay, Flanger, Reverb, Sustain, and Glide.
Selecting, playing, and using fill-in patterns for rhythm tracks.
Setting accompaniment types and using the Auto Bass Chord function.
Playing percussion sounds and adding harmony with Melody On Chord.
Saving custom settings to memory buttons and recalling them.
Using footswitches for shifting and panel buttons for data editing.
Performing a Power On Reset to clear all settings and user rhythms.
Precautions for disks, inserting/ejecting, cleaning, and formatting.
Step-by-step guides for recording songs, parts, and playing them back.
Covers Custom Play, Pause, Tempo changes, Song Copy/Delete, and Voice Disks.
Explains M.D.R. display messages and disk copy protection.
Outlines the process of creating custom rhythm patterns.
Details Step Write, Real Time Write, beat/quantize settings, and editing.
Connecting patterns to create sequences and playing them back.
Backing up custom rhythm patterns and sequences to disk.
Assigning rhythm and glide functions to footswitches.
Using the knee lever for Sustain and Melody On Chord control.
Adjusting the instrument's key setting in half-steps.
Fine-tuning the instrument's overall pitch.
Setting MIDI channels for Upper, Lower, and Pedalboard transmissions.
Configuring MIDI timing sync and expression pedal control.
Connecting external rhythm machines and audio sources.
Connecting headphones and how it affects speaker output.
Solutions for common operational and functional problems.
Detailed MIDI message charts, specifications, and implementation details.
To Next Page