Yamaha MG12XU User Manual (English)

Other manuals for Yamaha MG12XU

Questions and Answers:

J
Jason WhiteAug 17, 2025
Why are effects not working on my Yamaha Music Mixer?
- S
  stephanie97Aug 18, 2025
  If effects are not being applied on your Yamaha Music Mixer, check that the [FX] knobs for each channel are at suitable levels. Ensure the [ON] button for [FX RTN] is activated. Verify the [PARAMETER] knob and [FX RTN] fader are correctly adjusted. Confirm the [FX RTN] bus assign switch is properly set. If external effects are connected to the [SEND(AUX1 – 4)] jacks, make sure the [AUX1 – 4] knobs for [SEND MASTER] are appropriately set. Check that the power of that device is turned on.
D
David BrownAug 21, 2025
How to troubleshoot no sound output on Yamaha Music Mixer?
- M
  Mark SwansonAug 21, 2025
  If no sound is coming from the Yamaha Music Mixer, first, ensure external instruments and speakers are correctly connected and that cables aren't shorted. Check if the power of the device is turned on. Then, verify that the [GAIN] knobs for each channel, channel faders, [STEREO] master fader, and [GROUP] faders are at appropriate levels. Also, confirm that the bus assign switches and [LINE /USB] switch are correctly set.
K
kristina66Aug 25, 2025
What to do if there is no sound from [STEREO OUT] jack on Yamaha Music Mixer?
- T
  Teresa RiveraAug 26, 2025
  If you're not getting any sound from the [STEREO OUT] jack on your Yamaha Music Mixer, ensure that the [ON] and [ST] switches for the channels you're using are activated. Also, verify that the [STEREO] master [ON] switch is turned on. Check that the power of that device is turned on.
B
Bradley RhodesAug 27, 2025
How to fix no sound output from [SEND (AUX1 – 4)] jacks on Yamaha Music Mixer?
- K
  Kristen NunezAug 27, 2025
  If you're not getting any sound from the [SEND (AUX1 – 4)] jacks on your Yamaha Music Mixer, ensure that the [SEND MASTER] knobs and [AUX 1 – 4] for each channel are appropriately set. When the [PRE] switch for [AUX] is off, confirm that the [ON] switches for the channels you are using are turned on. Check that the power of that device is turned on.
M
Morgan MoodyAug 31, 2025
How to improve speaking voice clarity on Yamaha Music Mixer?
- T
  Tyler WrightAug 31, 2025
  If speech is unclear when using your Yamaha Music Mixer, ensure the [HPF] switch is turned on and the equalizer ([HIGH]/[MID]/[LOW]) is properly adjusted. Check that the power of that device is turned on.
E
Elizabeth RoblesSep 3, 2025
What causes unstable sound level on Yamaha Music Mixer?
- B
  Brian PerrySep 3, 2025
  If the sound level on your Yamaha Music Mixer is unstable and inconsistent, use the [COMP] knob to lower the compressor level, as it may be set too high.
B
Brittany FosterSep 6, 2025
How to troubleshoot no mixer monitor signal output on Yamaha Music Mixer?
- J
  Jonathan BakerSep 7, 2025
  Ensure powered speakers are connected to the [MONITOR OUT] jacks. Adjust the signal output from the [MONITOR OUT] jacks using the [MONITOR LEVEL] knob on your Yamaha Music Mixer.
C
Christian RodriguezSep 10, 2025
Why are left and right levels different on my Yamaha Music Mixer?
- C
  Cheryl MartinezSep 10, 2025
  If the left and right levels are different for a stereo signal input on your Yamaha Music Mixer, first ensure that [PAN] is set to the center. If it is, try reversing the left and right input connections. If the low volume switches sides after swapping connections, the issue is with the instrument or device sending the signal. Also, check that you're using the same type of cable for both left and right inputs, as cables with built-in resistors can reduce the signal. Check that the power of that device is turned on.

Yamaha MG12XU Specifications

General

Sample rate	192 kHz
Channels quantity	12 channels
Digital sound processing	24 bit
XLR out	2
Microphone in	Yes
Headphone connectivity	6.3 mm
DJ mixer	No
Power consumption (typical)	22 W