What does memory error mean on Yamaha Rio1608-D2 Recording Equipment?
If you are getting a memory error on your Yamaha Recording Equipment, information that was saved during the previous operation was lost, so this information must be reset.
How to fix Yamaha Rio1608-D2 Recording Equipment when the power won’t turn on?
If your Yamaha Recording Equipment isn't turning on, first, ensure the power cable is properly connected. Also, check that the [POWER] switch is turned ON. If it still doesn't power on after these steps, contact your Yamaha dealer.
What to do if Yamaha Rio1608-D2 Recording Equipment is not receiving an input signal?
If your Yamaha Recording Equipment isn't receiving an input signal, check these items: * Ensure the input cables are correctly connected. * Verify the source device is sending a signal and that the SIG indicators on the appropriate channels are lit. * Confirm the internal head amplifier gain is set correctly. * If the SETUP menu’s START UP MODE is set to REFRESH, ensure the Rio2-native device has started.
Why is the input level too low on my Yamaha Recording Equipment?
If the input level on your Yamaha Recording Equipment is too low, and you're using a condenser microphone, turn the [+48V MASTER] switch ON. Also, ensure that the internal head amplifier gain is set to an appropriate level.
What to do if Rio cannot be found in R Remote for Yamaha Rio1608-D2?
If the Rio is not found in R Remote for your Yamaha Recording Equipment, verify that the UNIT ID setting does not conflict with another R series unit by setting each UNIT ID uniquely. Also, check the IP address setting and ensure the network is correctly connected, verifying they are set to the same subnet. If the SECONDARY PORT parameter is set to REDUNDANT, ensure the unit is connected to the [PRIMARY] port.
What does power supply failure A or B mean on Yamaha Recording Equipment?
If you receive a 'Power Supply A (B) Failed' error on your Yamaha Recording Equipment, check that the power supply cable is connected. If checking does not resolve the problem, contact a Yamaha service center.
Why is Dante not working by Gigabit on my Yamaha Rio1608-D2?
If Dante is not working by Gigabit on your Yamaha Recording Equipment, and you are conveying audio via Dante, use devices that support gigabit Ethernet.
What to do if an error occurred at the secondary port on Yamaha Rio1608-D2 Recording Equipment?
If an error occurred at the secondary port on your Yamaha Recording Equipment, check the circuit that is connected to the [SECONDARY] port.
How to resolve Dante audio resource overflow on Yamaha Rio1608-D2?
If you encounter a Dante audio resource overflow on your Yamaha Recording Equipment, reconfigure the Dante audio routing. For example, eliminate unneeded routings, or use multicast rather than unicast to improve efficiency.
What to do when Gigabit network link fails on Yamaha Recording Equipment?
If the Gigabit network link failed and switched to 100Mbps (or 10Mbps) on your Yamaha Recording Equipment, check the link status. Try plugging into a different network switch or port. Alternatively, try using a different network cable.
Lists crucial safety instructions to prevent injury, electric shock, and device damage.
Covers safety measures for power, water, ventilation, and handling to prevent hazards.
Advises on preventing hearing damage, fire hazards, and responding to device abnormalities.
Provides essential guidelines for safely mounting the unit in an EIA standard rack to ensure proper ventilation and performance.
Advises against using the EEE function on network switches to prevent Dante synchronization issues.
Details the XLR input connectors, +48V, SIG, and PEAK indicators with safety cautions.
Details the PRIMARY/SECONDARY etherCON RJ45 ports for Dante networking and their indicators.
Describes how to adjust the HA gain value using the encoder, with a specified range and increment.
Shows how to set HA gain values for input ports, including compensation gain status.
Guides on turning the High-Pass Filter ON or OFF for selected input ports.
Details how to set the HPF cutoff frequency for input ports within a specific range.
Explains how to set the Gain Compensation ON/OFF status for input ports and view compensation gain values.
Describes the simple daisy chain connection method for small systems.
Details how to control head amplifiers remotely from Rio2-native devices.
Provides a table of common issues, their causes, and possible solutions for the unit.
Lists various error messages, their descriptions, and recommended solutions.
Details alert and warning messages, including firmware mismatches and network issues.
Describes synchronization messages, word clock issues, and Dante port connection problems.
General| XLR out | 16 |
|---|---|
| XLR inputs | 8 |
| Cable length | - m |
| Product color | Black |
Weight and Dimensions| Depth | 368 mm |
|---|---|
| Width | 480 mm |
| Height | 132 mm |
| Weight | 9600 g |
To Next Page
