To Next PageTo Next PageWhat to do if there is no sound from Yamaha Stereo Receiver?
If there's no sound from your Yamaha Stereo Receiver, ensure the input and output cables are correctly connected (and not defective). Select the appropriate input source using the INPUT selector on the front panel or the remote control. Make sure the SPEAKERS A/B switches are properly set and speaker connections are secure.
What to do if the volume level cannot be increased, or the sound is distorted on Yamaha RX-797 Stereo Receiver?
If the volume level cannot be increased, or the sound is distorted on your Yamaha Stereo Receiver, check if the component connected to the MD/ TAPE OUT jacks of the unit is turned off. If so, turn on the power of that component.
Why is the sound degraded when listening with the headphones connected to the CD player or the tape deck connected to Yamaha Stereo Receiver?
If the sound is degraded when listening with headphones connected to the CD player or tape deck connected to your Yamaha Stereo Receiver, ensure the power of the unit is turned on and that it is not set to standby mode.
Why is the sound level low on Yamaha Stereo Receiver?
If the sound level is low on your Yamaha Stereo Receiver, check if the LOUDNESS control is functioning. If it is, set the LOUDNESS control to the FLAT position.
What to do if the input source cannot be changed on Yamaha RX-797?
If the input source cannot be changed on your Yamaha Stereo Receiver even when the INPUT selector is rotated, check if the CD DIRECT AMP button is turned on. If it is, turn off the CD DIRECT AMP button.
Why using the BASS, TREBLE, BALANCE and LOUDNESS controls does not affect the tonal quality on Yamaha Stereo Receiver?
If using the BASS, TREBLE, BALANCE, and LOUDNESS controls does not affect the tonal quality on your Yamaha Stereo Receiver, the CD DIRECT AMP or the PURE DIRECT button may be turned on. Turn off the CD DIRECT AMP or the PURE DIRECT button to use those controls.
Why previously preset stations can no longer be tuned in on Yamaha RX-797 Stereo Receiver?
If previously preset stations can no longer be tuned in on your Yamaha Stereo Receiver, and the unit has been disconnected for a long period, preset the stations again.
Why the desired station cannot be tuned in with the automatic tuning method (AM) on Yamaha Stereo Receiver?
If the desired station cannot be tuned in with the automatic tuning method (AM) on your Yamaha Stereo Receiver, the signal may be weak or the antenna connections may be loose. Tighten the AM loop antenna connections and orient it for the best reception. You can also try using the manual tuning method.
Why are there continuous crackling and hissing noises on Yamaha Stereo Receiver?
If you are experiencing continuous crackling and hissing noises on your Yamaha Stereo Receiver, the noises may result from lightning, fluorescent lamps, motors, thermostats, or other electrical equipment. Try using an outdoor antenna and a ground wire, but note that it is difficult to eliminate all noise.
General| Impedance | 8 ohms |
|---|---|
| Signal-to-Noise Ratio | 100 dB (CD) |
| Speaker Load Impedance | 4 ohms to 16 ohms |
| Tuner Section | FM/AM |
| Power Output | 100W per channel (8 ohms, 20Hz-20kHz, 0.015% THD) |
| Frequency Response | 10 Hz-100 kHz +0, -3 dB |
| Total Harmonic Distortion | 0.015% |
| Tuning Range | FM |
| Input Sensitivity | 200mV (line) |
Identifies and emphasizes components requiring exact specification replacement.
Procedure to verify insulation and safety after servicing.
Illustration of the RAX100 remote control layout.
Illustration of the RAX101 remote control layout.
Illustration of the RAX17 remote control layout.
Illustration of the RAX18 remote control layout.
Output power, damping factor, input sensitivity, and tone control specifications.
Video signal types, levels, and frequency response characteristics.
Tuning range, sensitivity, selectivity, and signal-to-noise ratio for FM reception.
Tuning range, sensitivity, and signal-to-noise ratio for AM reception.
Power supply, power consumption, and AC outlet specifications.
Controls initialization of backup RAM, including protection history management.
Displays information related to XM Radio data reception.
Displays past protection triggers and their causes.
Shows microprocessor version, checksum, and software module status.
Pinout details for the display module's connections.
Mapping of display segments to input signals.
Connections related to the display's anode structure.
Pinout details for integrated circuits used in the unit.
Pinout and identification for various diodes.
Pinout and identification for various transistors.
Pinout and identification for field-effect transistors.
List of electronic components like capacitors, resistors, ICs, and transistors.
Detailed list of carbon resistors with various wattage types.
Circuit diagram for the RAX100/RAX101 remote controls.
Table of IR codes for various functions on the remote controls.
Circuit diagram for the RAX17 remote control.
List of IR command codes for the RAX17 remote.
Circuit diagram for the RAX18 remote control.
List of IR command codes for the RAX18 remote.
