Need help?Do you have a question about the Yamaha RX-V2092 and is the answer not in the manual?
General| Type | AV Receiver |
|---|---|
| Channels | 5.1 |
| Input Sensitivity (MM) | 2.5 mV |
| Input Sensitivity (line) | 150 mV |
| Signal to Noise Ratio (line) | 100 dB |
| Signal-to-Noise Ratio | 100dB (line) |
| Analog Inputs | 5 |
| Phono Input | Yes |
| Power Output | 100 W per channel (8 ohms) |
| Frequency Response | 20Hz to 20kHz |
| Damping Factor | 100 |
| Input Sensitivity/Impedance | 47 kOhm |
| Speaker Load Impedance | 8 ohms |
| Digital Inputs | Optical, Coaxial |
| Video Connections | Composite |
| Video Inputs/Outputs | 3 in, 1 out |
Details audio output power, impedance, sensitivity, and frequency response characteristics.
Covers FM tuning range, sensitivity, selectivity, and signal-to-noise ratio.
Specifies AM tuning range, sensitivity, selectivity, and signal-to-noise ratio.
Outlines video signal types, levels, and frequency response for video inputs.
Provides power supply, consumption, dimensions, weight, and accessories information.
Explains the self-diagnosis function for locating faulty parts and its operation.
Details how to start the diagnostic program and its initial settings.
Describes menu selection, display contents, and other operations during diagnosis.
Explains how to exit the diagnosis mode and return to normal operation.
Details the specific diagnostic modes and signal paths.
Describes the signal passage for the THROUGH diagnostic mode.
Details the signal path for the FRONT THROUGH diagnostic mode.
Explains the PRO LOGIC function activation and sub-menu settings.
Details signal output through AC3F for Dolby Digital and PCM signals.
Explains the test noise output to selected channels via sub-menu.
Describes the procedure for checking the VFD driver and segments.
Explains how to reserve or reset backup data to factory settings.
Details checking AD input ports and voltage division resistance values.
Shows model, market, and ROM version information.
Details exiting diagnosis and entering demonstration display mode.
Shows digital signal and digital processing status on the display.
Explains selectable center speaker modes: WIDE, NORMAL, PHANTOM.
Describes rear speaker settings: LARGE and SMALL.
Describes main speaker settings: LARGE and SMALL.
Explains bass output settings: SWFR, MAIN, and BOTH.
Default video input settings for factory preset.
Default ROOM 2 input settings for factory preset.
Default effect level settings for factory preset.
Default DSP program settings for factory preset.
Default set menu settings for factory preset.
Default preset station data for factory preset.
Lists necessary equipment for tuner adjustment procedures.
Identifies key test points on the circuit board for adjustments.
Describes antenna simulation circuits for testing.
Details procedures for adjusting FM reception parameters.
Details procedures for adjusting AM reception parameters.
Provides pin connection diagrams for display components.
Shows the grid assignment for display elements.
Details the anode connections for display components.
Foil side layout of the tuner printed circuit board.
Foil side layout of the function printed circuit board.
Foil side layout of the function printed circuit board.
Foil side layout of the function printed circuit board.
Foil side layout of the DSP printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the operation printed circuit board.
Foil side layout of the main printed circuit board.
Foil side layout of the main printed circuit board.
Foil side layout of the main printed circuit board.
Foil side layout of the main printed circuit board.
Foil side layout of the video printed circuit board.
Foil side layout of the video printed circuit board.
Foil side layout of the video printed circuit board.
Foil side layout of the video printed circuit board.
Foil side layout of the video board for U, C models.
Foil side layout of the video board for A, L models.
Foil side layout of the video board for R model.
Circuit diagram for the tuner section.
Circuit diagram for the function section.
Circuit diagram for the DSP section.
Circuit diagram for the operation section.
Circuit diagram for the main amplifier section.
Circuit diagram for the video section.
List of electronic components including capacitors, resistors, and ICs.
Parts list for the tuner and function boards.
Parts list for the function board.
Parts list for the function board.
Parts list for function and DSP boards.
Parts list for the DSP board.
Parts list for DSP and video boards.
Parts list for the video board.
Parts list for video and main boards.
Parts list for main and operation boards.
Parts list for the main board.
Parts list for the main board.
Parts list for main and operation boards.
Parts list for the operation board.
List of specific chip and flame-proof resistors.
Lists mechanical components and their assembly references.
Lists included accessories such as remote control and antennas.
Circuit diagram of the remote control transmitter.
Table of fixed transmission codes for remote control buttons.
To Next Page
