Yamaha RX-V2300 User Manual (English)

Other manuals for Yamaha RX-V2300

Questions and Answers:

S
Sarah NelsonAug 16, 2025
What to do if there is no sound from the center speaker of my Yamaha RX-V2300?
- E
  Ernest LongAug 16, 2025
  If you're not getting any sound from the center speaker of your Yamaha Receiver, here are a few things to check: 1. Make sure the output level of the center speaker isn't set to minimum. Raise the level if needed. 2. Verify that “1A CENTER SP” on the SET MENU is not set to NONE. Select the appropriate mode for your center speaker. 3. If one of the Hi-Fi DSP programs (1 to 6 except for Game and 6ch Stereo) is selected, try selecting another DSP program.
R
randy81Aug 19, 2025
What to do if my Yamaha RX-V2300 Receiver fails to turn on?
- M
  maldonadoleonAug 19, 2025
  If your Yamaha Receiver fails to turn on, there are several potential causes: * Ensure the power cord is firmly connected. * If the IMPEDANCE SELECTOR switch on the rear panel is not fully set to the left or right, set it fully to either position while the unit is in standby mode. * Check speaker wire connections to ensure they are secure and not touching anything other than their respective connections, as the protection circuitry might have been activated. * If the unit has been exposed to a strong electric shock, set it to standby, disconnect the power cord, wait 30 seconds, and then plug it back in.
J
Jennifer WestAug 22, 2025
Why does my Yamaha RX-V2300 Receiver suddenly turn into standby mode?
- A
  Ashley SmithAug 22, 2025
  Your Yamaha Receiver might be turning into standby mode because the internal temperature has become too high, activating the overheat protection circuitry. Wait for the unit to cool down before turning it back on.
J
josephcardenasAug 26, 2025
How to fix a humming sound from Yamaha RX-V2300 Receiver?
- N
  Nicole RubioAug 26, 2025
  A humming sound from your Yamaha Receiver can often be resolved by checking the following: * Ensure all audio plugs are firmly connected. If the problem continues, the cables may be defective. * If you have a turntable, make sure its grounding cord is connected to the GND terminal of the unit.
D
David BlackwellAug 28, 2025
What to do if there is no sound from the rear speakers of my Yamaha RX-V2300?
- H
  hardysierraAug 28, 2025
  If you're experiencing no sound from the rear speakers of your Yamaha Receiver, consider the following: * Ensure the output level of the rear speakers is not set to minimum. Adjust the level as necessary. * Check that “1C REAR L/R SP” on the SET MENU is not set to NONE. Select the appropriate speaker mode for the rear L/R speakers. * If a monaural source is being played with program 10, select another DSP program.
C
Chad RobinsonAug 31, 2025
What to do if Dolby Digital or DTS sources cannot be played on my Yamaha RX-V2300?
- I
  iclarkAug 31, 2025
  If your Yamaha Receiver isn't playing Dolby Digital or DTS sources, make sure that “Digital output” and “Dolby Digital” or “DTS” are selected on the connected components. Refer to the operation instructions for your component to make the appropriate settings.
F
Frederick RobinsonSep 3, 2025
What to do if there is no sound from the subwoofer of my Yamaha RX-V2300?
- T
  tanya35Sep 3, 2025
  If you're not getting any sound from the subwoofer connected to your Yamaha Receiver, check these settings: * If a Dolby Digital or DTS signal is being played, ensure “1E LFE/BASS OUT” on the SET MENU is set to SWFR or BOTH. * If a 2-channel source is being played, ensure “1E LFE/BASS OUT” on the SET MENU is set to BOTH. * Also, the source may not contain low bass signals (90 Hz and below).
H
Heather GutierrezSep 6, 2025
Why can't I change the sound field parameters on my Yamaha Receiver?
- C
  Chad WilliamsSep 6, 2025
  If you're unable to change the sound field parameters and some other settings on your Yamaha Receiver, check if “14 MEMORY GUARD” on the SET MENU is set to ON. If it is, select OFF.
M
Michael SandersSep 9, 2025
Why is the sound degraded when listening with headphones connected to a tape deck or CD player that is connected to my Yamaha Receiver?
- H
  Holly BarajasSep 9, 2025
  If the sound quality is degraded when listening with headphones connected to a tape deck or CD player that's connected to your Yamaha Receiver, make sure the unit is not in standby mode. Turn on the power of the unit.
E
edwardfrancoSep 12, 2025
What to do if there is noise interference from digital equipment on my Yamaha RX-V2300 Receiver?
- K
  Kimberly WilsonSep 12, 2025
  If you are experiencing noise interference from digital or high-frequency equipment with your Yamaha Receiver, the unit may be too close to the equipment. Move the unit further away from such equipment.

Yamaha RX-V2300 Specifications

General

Type	AV Receiver
Audio Channels	7.1
Channels	7
Amplifier Type	Discrete
Total Harmonic Distortion	0.04 %
Weight	20.5 kg
Input Sensitivity	200 mV
Signal to Noise Ratio	100 dB
Video Inputs	5
Video Outputs	2
Signal-to-Noise Ratio	100 dB
Audio Inputs	6
Audio Outputs	2
Tuner	AM/FM
Preset Stations	40
Remote Control	Yes
THD	0.04%
Frequency Response	10 Hz - 100 kHz
Surround Sound Formats	Dolby Digital, DTS
Speaker Load Impedance	8 ohms
Inputs	6 audio, 6 video, 3 component video, 3 digital audio (2 optical, 1 coaxial)
Digital inputs	3 (2 optical, 1 coaxial)
Dimensions (W x H x D)	435 x 171 x 468 mm

Summary

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Reduce risk of electric shock by not removing cover; refer servicing to qualified personnel.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT

WARNING

Warning to reduce risk of fire or electric shock.

FEATURES

Built-in 6-Channel Power Amplifier

Details on RMS output power for main, center, and rear channels.

Multi-Mode Digital Sound Field Processing

Lists DSP technologies like Dolby Pro Logic II, Dolby Digital, DTS, CINEMA DSP.

Sophisticated AM/FM Tuner

Features like 40-station preset tuning and auto tuning.

Other Features

Lists items like D/A converter, SET MENU, test tone generator, etc.

GETTING STARTED

Checking the Package Contents

Lists items included in the package.

Installing Batteries in the Remote Control

Instructions on how to insert batteries into the remote control.

CONTROLS AND FUNCTIONS

Front Panel

Explains the buttons and indicators on the front panel of the unit.

CONTROLS AND FUNCTIONS

REC OUT/ZONE 2 (U.S.A., Canada and Australia models)

Selects source for audio/video recorder and Zone 2 outputs.

TUNING MODE (AUTO/MAN'L MONO)

Switches between automatic and manual tuning modes.

CONTROLS AND FUNCTIONS

Remote Control

Describes the controls and functions of the remote control.

CONTROLS AND FUNCTIONS

MACRO

Used to program a series of operations for control by a single button.

Using the Remote Control

Provides guidance on how to use the remote control effectively.

CONTROLS AND FUNCTIONS

Front Panel Display

Explains the indicators and display on the front panel.

CONTROLS AND FUNCTIONS

Rear Panel

Details the various input and output jacks on the rear panel.

SPEAKER SETUP

Speakers to Be Used

Explains suitable speaker types and configurations for optimal sound.

Speaker Placement

Provides diagrams and guidance for optimal speaker placement.

SPEAKER SETUP

Connecting the Speakers

Instructions on connecting speaker cables to the unit's terminals.

SPEAKER SETUP

SUBWOOFER jack

Details the connection and function of the subwoofer jack.

SPEAKER SETUP

IMPEDANCE SELECTOR switch

Explains how to match amplifier output to speaker impedance using the switch.

CONNECTIONS

Before Connecting Components

Important precautions and general advice before making connections.

Connecting Video Components

Explains how to connect video sources like VIDEO, S VIDEO, and COMPONENT VIDEO.

CONNECTIONS

Connecting the Antennas

Instructions for connecting AM and FM antennas.

CONNECTIONS

Connecting Audio Components

Instructions for connecting digital audio sources, CD players, and turntables.

CONNECTIONS

Connecting the Power Supply Cords

Instructions for connecting the power cord and using switched AC outlets.

CONNECTIONS

Turning on the Power

Steps to power on the unit and connected video monitor.

PREPARATION

ON-SCREEN DISPLAY (OSD)

How to display operation information on a video monitor.

PREPARATION

Selecting the OSD Mode

How to change the OSD display mode (full, short, off).

SPEAKER MODE SETTINGS

Summary of SPEAKER SET Items 1A through 1G

Summarizes speaker set items for configuring speaker output modes.

ADJUSTING THE SPEAKER OUTPUT LEVELS

Before You Begin

Preparatory steps before adjusting speaker levels.

Using the Test Tone (TEST DOLBY SUR.)

Using the test tone generator to balance speaker output levels.

BASIC PLAYBACK

Input Modes and Indications

Explains how to set input signal priority and understand input indications.

BASIC PLAYBACK

Selecting a Sound Field Program

How to select and enjoy different DSP sound field programs.

BASIC PLAYBACK

Selecting PRO LOGIC, PRO LOGIC II or Neo: 6

How to select these decoding modes for 2-channel sources.

Playing the Dolby Digital EX or DTS ES software

How to use EX/ES decoders for specific software.

BASIC PLAYBACK

Normal Stereo Reproduction

How to turn off sound effects for normal stereo playback.

Displaying the information about the input source

How to view signal type, format, and sampling frequency of the input.

DIGITAL SOUND FIELD PROCESSING (DSP)

Understanding Sound Fields

Explains the concept of sound fields and their elements.

Hi-Fi DSP Programs

Describes DSP programs for recreating concert hall/opera house acoustics.

CINEMA-DSP

Yamaha's DSP for movie soundtracks, integrating DTS and Dolby.

DIGITAL SOUND FIELD PROCESSING (DSP)

Straight Decode

Using built-in decoders without added sound effects.

Sound Field Effect

Explains how MOVIE THEATER programs recreate sound fields.

DIGITAL SOUND FIELD PROCESSING (DSP)

Features of DSP Programs

Brief descriptions of various DSP programs like CONCERT HALL, CHURCH, JAZZ CLUB.

DIGITAL SOUND FIELD PROCESSING (DSP)

CINEMA DSP Features

Details on CINEMA DSP programs like MOVIE THEATER 1, MOVIE THEATER 2.

DIGITAL SOUND FIELD PROCESSING (DSP)

Table of Program Names for Each Input Format

Maps DSP programs to input formats and decoder settings.

TUNING

Automatic and Manual Tuning

Explains automatic and manual tuning methods for stations.

TUNING

Presetting Stations

How to automatically preset FM stations.

Automatic preset tuning options

Options for automatic preset tuning.

TUNING

Manually presetting stations

Steps for manually storing up to 40 stations.

TUNING

Tuning in to a Preset Station

How to tune to a stored station by selecting its number.

Exchanging Preset Stations

Procedure to swap assignments of two preset stations.

BASIC RECORDING

REC OUT/ZONE 2 or REC OUT

How to record one source while watching/listening to another.

BASIC RECORDING

Special considerations when recording DTS software

Adjustments needed for recording DTS signals.

Timer playback/recording

How to perform playback or recording using an external timer.

REMOTE CONTROL FEATURES

Control Area

Identifies the control areas on the remote for the unit and other components.

REMOTE CONTROL FEATURES

Setting the Manufacturer Code

How to set manufacturer codes to control other components.

REMOTE CONTROL FEATURES

LEARN Feature

How to program new functions not covered by manufacturer codes.

REMOTE CONTROL FEATURES

Changing the Source Name in the Display Window

How to rename input source names on the remote's display.

REMOTE CONTROL FEATURES

Using the Macro Feature

How to program and use macros for single-button operations.

REMOTE CONTROL FEATURES

Operating the macro

How to operate programmed macros.

REMOTE CONTROL FEATURES

Clearing Learned Functions, Macros, Renamed Source Names, and Setup Manufacturer Codes

Procedures for clearing programmed remote functions.

REMOTE CONTROL FEATURES

Clearing a Learned Function

How to clear learned functions for specific buttons.

Clearing a macro function

How to clear programmed macro functions.

REMOTE CONTROL FEATURES

SOURCE SELECT △ / ∇

How to select components for remote control without changing input.

OPTN (option) area

Control area for extra components programmed separately.

REMOTE CONTROL FEATURES

Zone 2 (U.S.A., Canada and Australia models only)

Setting up the remote for Zone 2 multi-room control.

REMOTE CONTROL FEATURES

Operating a DVD player (DVD area)

Controls for operating a DVD player via the remote.

REMOTE CONTROL FEATURES

Operating a VCR (VCR 1 and VCR 2/DVR areas)

Controls for operating VCRs via the remote.

REMOTE CONTROL FEATURES

Operating a TV/digital TV (D-TV/LD area) or a cable TV/satellite TV (CBL/SAT area)

Controls for operating TVs and cable/satellite tuners.

REMOTE CONTROL FEATURES

Operating an LD player (D-TV/LD area)

Controls for operating LD players via the remote.

REMOTE CONTROL FEATURES

Operating a CD player (CD area)

Controls for operating CD players via the remote.

REMOTE CONTROL FEATURES

Operating a CD recorder (CD-R area) or an MD recorder (MD/TAPE area)

Controls for CD recorders and MD recorders.

REMOTE CONTROL FEATURES

Operating a tape deck (MD/TAPE area)

Controls for operating tape decks via the remote.

REMOTE CONTROL FEATURES

Operating a tuner (TUNER area)

Controls for operating tuners via the remote.

REMOTE CONTROL FEATURES

Operating the component set in A or B

Instructions for setting up components in control areas A or B.

SET MENU

Adjusting the Items on the SET MENU

Explains how to adjust items within the SET MENU using the remote.

SET MENU

1 SPEAKER SET (speaker mode settings)

Selects output modes based on speaker configuration and size.

2 LOW FRQ TEST

Adjusts subwoofer output level to match other speakers.

SET MENU

1A CENTER SP (center speaker mode)

Configures center speaker output based on its size or absence.

1B MAIN SP (main speaker mode)

Configures main speaker output based on size (large/small).

SET MENU

1C REAR L/R SP (rear speaker mode)

Configures rear speaker output based on size or absence.

1D REAR CT SP (rear center speaker mode)

Configures rear center speaker output based on size or absence.

SET MENU

1E LFE/BASS OUT (bass out mode)

Selects output for LFE/low bass signals (subwoofer, main, or both).

1F MAIN LEVEL (main level mode)

Adjusts main speaker output level relative to effect speakers.

SET MENU

1G SP B SET (speaker B set)

Selects location for speakers connected to SPEAKERS B terminals.

15 6CH INPUT SET

Sets signal direction for center and subwoofer channels for 6CH INPUT.

SET MENU

16 ZONE 2 SET

Settings for audio output to ZONE 2 (output volume, speaker assignment).

SLEEP TIMER

Setting the Sleep Timer

How to set the unit to automatically enter standby mode after a set time.

Canceling the Sleep Timer

How to cancel the sleep timer.

SOUND FIELD PROGRAM PARAMETER EDITING

What Is a Sound Field?

Explains the concept of sound fields and their elements.

Sound Field Program Parameters

Explains parameters that determine acoustic environment and how to adjust them.

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

DSP LEVEL

Adjusts the overall level of DSP effect sounds relative to the direct sound.

INIT. DLY (Initial Delay)

Changes apparent distance by adjusting delay between direct sound and first reflection.

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

ROOM SIZE

Adjusts the apparent size of the surround sound field.

LIVENESS

Adjusts virtual wall reflectivity by changing early reflection decay rate.

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

S. DELAY (Surround Delay)

Adjusts delay for surround signals and surround sound field.

S. INIT. DLY (Surround Initial Delay)

Adjusts delay between direct sound and first reflection for surround.

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

REV. TIME (Reverberation Time)

Adjusts time for dense reverberation sound to decay.

REV. DELAY (Reverberation Delay)

Adjusts time difference between direct sound and reverberation sound.

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

For 6ch Stereo

Parameters for adjusting channel levels in 6-channel stereo mode.

For PRO LOGIC II Music

Parameters like PANORAMA, DIMENSION, CT WIDTH for Pro Logic II Music.

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

For DTS Neo: 6 Music

Parameter C. IMAGE for DTS Neo: 6 Music.

TROUBLESHOOTING

General

Common problems and their remedies for the unit.

TROUBLESHOOTING

Tuner

Troubleshooting common issues with FM/AM reception and tuning.

TROUBLESHOOTING

Remote control

Troubleshooting issues with the remote control not working or learning functions.

GLOSSARY

Dolby Surround

Explanation of the Dolby Surround analog recording system.

Dolby Digital

Explanation of the Dolby Digital digital surround sound system.

GLOSSARY

Dolby Digital Surround EX

Unit's Dolby Digital decoder for 5.1 sources with rear center channel.

Dolby Pro Logic II

Improved technique to decode existing Dolby Surround programs.

GLOSSARY

DTS (Digital Theater Systems) Digital Surround

DTS digital surround for multi-channel audio soundtracks.

Neo: 6

Decodes 2-channel sources for 6-channel playback.

GLOSSARY

LFE 0.1 channel

Channel for reproduction of low bass signals (20 Hz to 120 Hz).

CINEMA DSP

Yamaha's DSP for movie soundtracks, integrating DTS/Dolby.

GLOSSARY

SILENT CINEMA

Natural, realistic sound effect DSP algorithm for headphones.

Virtual CINEMA DSP

Enjoy DSP surround effects without rear speakers using virtual rear speakers.

GLOSSARY

Sampling frequency and number of quantized bits

Explains sampling frequency and quantized bits in digital audio signals.

I/O assignment (SET MENU)

Assigns jacks according to components for effective connection.

SPECIFICATIONS

AUDIO SECTION

Technical specifications for the audio components.

SPECIFICATIONS

FM SECTION

Technical specifications for the FM tuner section.

AM SECTION

Technical specifications for the AM tuner section.

GENERAL

General specifications including power supply, consumption, and dimensions.

Related product manuals

Yamaha RX-V2300 User Manual

Table of Contents

Other manuals for Yamaha RX-V2300

Questions and Answers:

Yamaha RX-V2300 Specifications

Summary

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT

WARNING

FEATURES

Built-in 6-Channel Power Amplifier

Multi-Mode Digital Sound Field Processing

Sophisticated AM/FM Tuner

Other Features

GETTING STARTED

Checking the Package Contents

Installing Batteries in the Remote Control

CONTROLS AND FUNCTIONS

Front Panel

CONTROLS AND FUNCTIONS

REC OUT/ZONE 2 (U.S.A., Canada and Australia models)

TUNING MODE (AUTO/MAN'L MONO)

CONTROLS AND FUNCTIONS

Remote Control

CONTROLS AND FUNCTIONS

MACRO

Using the Remote Control

CONTROLS AND FUNCTIONS

Front Panel Display

CONTROLS AND FUNCTIONS

Rear Panel

SPEAKER SETUP

Speakers to Be Used

Speaker Placement

SPEAKER SETUP

Connecting the Speakers

SPEAKER SETUP

SUBWOOFER jack

SPEAKER SETUP

IMPEDANCE SELECTOR switch

CONNECTIONS

Before Connecting Components

Connecting Video Components

CONNECTIONS

Connecting the Antennas

CONNECTIONS

Connecting Audio Components

CONNECTIONS

Connecting the Power Supply Cords

CONNECTIONS

Turning on the Power

PREPARATION

ON-SCREEN DISPLAY (OSD)

PREPARATION

Selecting the OSD Mode

SPEAKER MODE SETTINGS

Summary of SPEAKER SET Items 1A through 1G

ADJUSTING THE SPEAKER OUTPUT LEVELS

Before You Begin

Using the Test Tone (TEST DOLBY SUR.)

BASIC PLAYBACK

Input Modes and Indications

BASIC PLAYBACK

Selecting a Sound Field Program

BASIC PLAYBACK

Selecting PRO LOGIC, PRO LOGIC II or Neo: 6

Playing the Dolby Digital EX or DTS ES software

BASIC PLAYBACK

Normal Stereo Reproduction

Displaying the information about the input source

DIGITAL SOUND FIELD PROCESSING (DSP)

Understanding Sound Fields

Hi-Fi DSP Programs

CINEMA-DSP

DIGITAL SOUND FIELD PROCESSING (DSP)

Straight Decode

Sound Field Effect

DIGITAL SOUND FIELD PROCESSING (DSP)

Features of DSP Programs