To Next PageTo Next PageWhy is sound only heard from one speaker on Yamaha RX-V3800 Receiver?
If you only hear sound from one side of the speaker when using your Yamaha Receiver, check the cable connections to ensure they are properly connected. If the problem persists, the cables may be defective. Also, verify the “Speaker Level” settings and adjust them as needed.
Why does the sound suddenly go off on my Yamaha RX-V3800 Receiver?
If the sound suddenly goes off on your Yamaha Receiver, it might be due to the activation of the protection circuitry, possibly due to a short circuit. Check that the speaker impedance setting is correct.
What to do if Yamaha RX-V3800 Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, ensure the power cable is firmly connected. Also, check that the speaker impedance setting matches your speakers. Secure all speaker wire connections, making sure the wires don't touch anything other than their respective connections. If the unit experienced a strong electric shock, put it in standby mode, disconnect the power cable, wait 30 seconds, and then plug it back in.
Why is my Yamaha Receiver remote control not working?
If the remote control for your Yamaha Receiver isn't working properly, replace the batteries. Also, make sure the remote controls are placed at the proper distance from the unit.
Why is no sound heard from the center speaker of my Yamaha Receiver?
If you're not hearing sound from the center speaker of your Yamaha Receiver, it might be because you are using a source or program combination that does not output sound from all channels. Set “Center” to “Small” or “Large.
What to do if the sound suddenly goes off on my Yamaha RX-V3800 Receiver?
If the sound suddenly goes off on your Yamaha Receiver, the protection circuitry may have been activated due to a short circuit. Check that the speaker impedance setting is correct and that the speaker wires are not touching each other, then turn the unit back on.
Why does my Yamaha RX-V3800 suddenly go into standby mode?
If your Yamaha Receiver suddenly enters standby mode, it may be due to overheating. Wait about 1 hour for the unit to cool down, and then try turning it back on.
How to fix 'CHECK SP WIRES' on Yamaha Receiver?
If your Yamaha Receiver displays 'CHECK SP WIRES' on the front panel, it indicates that the speaker cables are short-circuited. Ensure all speaker cables are correctly connected.
What to do if my Yamaha RX-V3800 Receiver fails to turn on or enters standby mode?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, consider the following: * Ensure the power cable is firmly connected. * Verify that the speaker impedance setting matches your speakers. * Check speaker wire connections to ensure they are secure and not touching anything other than their respective connections, as the protection circuitry may have been activated. * If the unit was exposed to a strong electric shock, set it to standby mode, disconnect the power cable, wait 30 seconds, and then plug it back in.
How to stop a humming sound from my Yamaha RX-V3800 Receiver?
To address a humming sound coming from your Yamaha Receiver, ensure the audio cables are firmly connected. If the problem persists, the cables may be defective.
General| Audio Channels | 7.1 |
|---|---|
| Amplifier Type | Discrete |
| THD (Total Harmonic Distortion) | 0.04% |
| Signal-to-Noise Ratio | 100 dB |
| HDMI Inputs | 4 |
| HDMI Outputs | 2 |
| HDMI Version | 1.3a |
| Dolby Digital | Yes |
| DTS | Yes |
| Surround Sound | Yes |
| Component Video Input | 3 |
| Component Video Output | 1 |
| S-Video Input | 4 |
| S-Video Output | 1 |
| Composite Video Input | 5 |
| Composite Video Output | 1 |
| Digital Audio Input (Coaxial) | 3 |
| Analog Audio Input | 6 |
| Weight | 37.5 lbs |
| Input Sensitivity | 200 mV |
| Power Output | 140 Watts (8 ohms, 20 Hz - 20 kHz, 0.04% THD, 2 channels driven) |
| Frequency Response | 10 Hz - 100 kHz |
Layout of the Digital Signal Processor Printed Circuit Board on Side A.
List of electrical components with warnings and special characteristics.
Settings for speaker impedance, remote sensor, and RS-232C.
