Why is FM stereo reception noisy on my Yamaha Receiver?
Noisy FM stereo reception on your Yamaha Receiver can occur if the transmitter is too far away or the antenna input is poor. Check the antenna connections and consider using a high-quality directional FM antenna.
Why won't my Yamaha RX-V520RDS Receiver turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, there could be several reasons. First, ensure the power cord is firmly connected to the unit and the outlet. Next, check that the IMPEDANCE SELECTOR switch on the rear panel is fully set to either the left or right position while the unit is in standby mode. Finally, the protection circuit might have been activated. In this case, verify that all speaker wire connections are secure and that no wires are touching anything other than their respective connections.
Why is there no sound or picture on my Yamaha Receiver?
If you're experiencing no sound or picture from your Yamaha Receiver, start by checking the input and output cable connections to ensure they are properly connected and not defective. Then, verify that you have selected the correct input source using the INPUT l / h, 6CH INPUT, or the input selector buttons. Also, check the speaker connections to make sure they are secure and that the correct main speakers are selected with SPEAKERS A and/or B. Finally, ensure the volume is not turned down or muted by pressing MUTE or any operation buttons and adjusting the volume. If you are inputting digital signals, ensure that they are PCM audio, Dolby Digital, or DTS signals that the unit can reproduce.
Why is there no sound from the subwoofer on my Yamaha RX-V520RDS Receiver?
If there is no sound from the subwoofer connected to your Yamaha Receiver, check the “BASS OUT” setting in the SET MENU. If you are playing a Dolby Digital or DTS signal, ensure it is set to SWFR or BOTH. If you are playing a 2-channel source, set it to BOTH.
Why is there no sound from the center speaker on my Yamaha Receiver?
If you're not getting any sound from the center speaker of your Yamaha Receiver, first check if the output level of the center speaker is set to minimum and raise it if necessary. Also, verify that “CENTER SP” in the SET MENU is not set to NON and select the appropriate mode for your center speaker. Finally, if one of the Hi-Fi DSP programs (1 to 4) is selected, try selecting another DSP program.
Why is there no sound from the rear speakers on my Yamaha RX-V520RDS?
If you are experiencing no sound from the rear speakers connected to your Yamaha Receiver, ensure that the output level of the rear speakers is not set to minimum and raise it if necessary. Also, if you are playing a monaural source with program 9, select another DSP program.
Why can't I control my Yamaha RX-V520RDS Receiver or other components with the remote?
If the unit or another component cannot be controlled with your Yamaha Receiver's remote, first press one of the component selector buttons corresponding to the component you want to control. If that doesn't work, the manufacturer code may not be set up correctly; try entering the code again.
Why can't I change the settings on my Yamaha RX-V520RDS Receiver?
If you cannot change the settings of the SET MENU and some other settings on your Yamaha Receiver, check if “9 MEM. GUARD” in the SET MENU is set to ON. If it is, select OFF.
Why can I hear a humming sound from my Yamaha RX-V520RDS Receiver?
If you hear a humming sound from your Yamaha Receiver, make sure the audio plugs are firmly connected. If the problem continues, the cables may be defective and need to be replaced.
How to improve bass reproduction on Yamaha RX-V520RDS Receiver?
If you're experiencing poor bass reproduction with your Yamaha Receiver, and “BASS OUT” in the SET MENU is set to SWFR or BOTH but you don't have a subwoofer, select MAIN. Also, ensure the output mode for each speaker (main, center, or rear) in the SET MENU matches your speaker configuration and select the appropriate output mode based on the size of your speakers.
Critical safety instructions for operating the unit.
Details on the unit's 5-channel power output.
Detailed description of the unit's front panel buttons and display.
How to connect digital and analog audio components.
Guide for connecting video components like DVD players and VCRs.
Detailed instructions for wiring speakers to the unit.
Using the test tone to balance speaker output levels.
How to choose and manage input signals for playback.
Adjusting speaker modes (MAIN, CENTER, REAR).
Adjusting BASS OUT, MAIN LVL, HP TONE CTRL, I/O ASSIGN.
Configuring INPUT MODE, DOLBY D. SET, DTS SET, D-RANGE.
Setting delay for DSP programs based on speaker distance.
Adjusting levels for center, rear, and subwoofer.
Programming the remote for other brands.
Common issues and their solutions.
Troubleshooting radio reception and remote control.
General| Type | AV Receiver |
|---|---|
| Channels | 5.1 |
| Power Output | 100 W |
| Power Output (8 ohms) | 100 W |
| Frequency Response | 10 Hz - 100 kHz |
| Total Harmonic Distortion | 0.06% |
| Input Sensitivity | 200 mV |
| Input Sensitivity (MM) | 2.5 mV |
| Input Sensitivity (line) | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Signal to Noise Ratio (line) | 100 dB |
| Weight | 10.5kg |
| Tuner Section | FM/AM |
| Speaker load impedance | 8 ohms |
| Digital inputs | 2 optical, 1 coaxial |
| Video Connections | composite |
| Dimensions | 435 x 151 x 363 mm |
| FM Sensitivity | 1.0 µV |
| Surround Sound | Dolby Pro Logic |
To Next Page
