To Next PageTo Next PageHow to reset my Yamaha Tuner?
If your Yamaha Tuner is not operating properly, the internal microcomputer might be frozen due to an external electric shock or a power supply with low voltage. Disconnect the AC power plug from the outlet and then plug it in again after about 30 seconds to reset it.
Why does my Yamaha T-S500 Tuner have continuous crackling and hissing noises?
Continuous crackling and hissing noises in your Yamaha Tuner can be caused by electrical equipment like lightning, fluorescent lamps, motors, or thermostats. Try using an outdoor antenna and a ground wire to reduce the noise. Be aware that it may be difficult to eliminate all noise completely.
What to do if my Yamaha T-S500 Tuner fails to turn on?
If your Yamaha Tuner fails to turn on when the POWER button is pressed, ensure the power cord is firmly connected. If the issue persists, it might have been exposed to a strong external electric shock. In this case, disconnect the power cord, wait 30 seconds, and then plug it back in.
Why is my Yamaha T-S500 humming?
If you hear a humming sound from your Yamaha Tuner, check the audio connection cord plugs to ensure they are firmly connected. If the problem persists, the cables may be defective and need replacement.
What to do if my Yamaha T-S500 Tuner has distortion?
If you experience distortion and cannot get clear reception even with a good FM antenna on your Yamaha Tuner, it may be due to multi-path interference. Adjust the antenna position to eliminate this interference.
Why can't I tune into stations automatically on my Yamaha Tuner?
If you cannot tune into the desired station using the automatic tuning method on your Yamaha Tuner, it could be due to a weak signal or loose antenna connections. Tighten the AM loop antenna connections and orient it for the best reception. Alternatively, try using the manual tuning method.
What to do if my Yamaha T-S500 has buzzing noises?
Buzzing and whining noises in your Yamaha Tuner can be caused by nearby TV sets. To resolve this, move the Yamaha Tuner away from the TV set.
Why is the FM stereo reception noisy on my Yamaha Tuner?
Noisy FM stereo reception on your Yamaha Tuner may occur due to the distance from the transmitter or a poor antenna input. First, check the antenna connections. If the issue persists, consider using a high-quality directional FM antenna to improve reception.
How to stop crackling noises on my Yamaha T-S500 Tuner?
Continuous crackling and hissing noises in your Yamaha Tuner can be caused by electrical interference from sources like lightning, fluorescent lamps, motors, or thermostats. Try using an outdoor antenna and a ground wire to minimize the noise. Keep in mind that it may be difficult to eliminate all noise completely.
What to do if my Yamaha T-S500 Tuner doesn't turn on?
If your Yamaha Tuner fails to turn on when you press the power button, make sure the power cord is securely connected to both the unit and the power outlet. If it still doesn't turn on, it may have been exposed to a strong electrical shock. In this case, disconnect the power cord, wait 30 seconds, and then plug it back in to restore normal operation.
General| Signal-to-Noise Ratio (SNR) | 75 dB |
|---|---|
| Total Harmonic Distortion (THD) | 0.5 % |
Weight and Dimensions| Depth | 306 mm |
|---|---|
| Width | 435 mm |
| Height | 87 mm |
| Weight | 3200 g |
Details the layout and functions of the unit's front panel controls and display.
Explains how to operate the unit using its remote control sensor.
Guides on connecting FM/AM antennas and audio output to an amplifier.
Step-by-step guide for automatically finding radio stations.
Instructions for manually tuning to specific radio frequencies.
How to recall previously stored radio stations.
Automatically stores strong FM stations to preset memory slots.
Manually stores selected stations to preset memory slots.
Steps to delete individual or all stored preset stations.
How to view RDS information like program service, type, and text.
Automatically searches for stations broadcasting traffic programs (TP).
Addresses issues like noisy stereo reception, distortion, and RDS errors.
Covers crackling, hissing, buzzing, and whining noises in AM reception.
Solutions for unit not turning on, humming sounds, or general non-operation.
