Home
Yanmar
Outboard Motor
Stern-Drive ZT370
Yanmar Stern-Drive ZT370 - User Manual
58 pages
Manual
Specs
Ask a question
Save Page as PDF
To Next Page
To Next Page
Loading...
2
Table of Contents
Main Page
Cover
1
Table of Contents
3
Introduction
5
Record of Ownership
6
Safety
7
Safety Precautions
8
General Information
8
Before You Operate
8
During Operation and Maintenance
8
Product Overview
13
Overview
13
Owner/Operator Responsibilities
13
New Stern-Drive Break-In:
13
Dealer/Distributor Responsibilities
14
Component Identification
15
Corrosion Protection
17
Galvanic Corrosion
17
Corrosion Control
17
Shore Power
17
Underwater Drive Coating
18
Additional Protection
18
Gear Housing Anodic Plates
19
Ventilation Plate Anode
19
Trim Cylinder Anodes
19
Propeller Shaft Anode
19
Features and Controls
20
Remote Controls
20
Power Trim
20
Stern-Drive Trim Angle
21
Trim and Tilt/Trailering Switch
21
Electrical System
22
Stern-Drive Operation
25
Propeller Selection
26
Installing the Propellers
27
Removing the Propeller
29
Daily Checks
29
Visual Checks
29
Check the Stern-Drive Oil Level
30
Fill the stern-drive with oil
30
Check the Power Trim Pump Fluid
31
Fill the power trim pump fluid
32
Maintenance
33
Periodic Maintenance
34
The Importance of Periodic Maintenance
34
Performing Periodic Maintenance
34
The Importance of Daily Checks
34
Yanmar Replacement Parts
34
Tools Required
34
Ask Your Authorized Yanmar Marine Dealer or Distributor for Help
34
Tightening Fasteners
35
Torque Charts
35
Standard Torque Values
35
Torque Specifications
35
Periodic Maintenance Table
36
General Inspection
38
Power Trim Pump Fluid
38
Periodic Maintenance Procedures
39
Weekly
39
Checking the water inlets
39
Checking the seawater inlet hole
39
Inspecting the anodes
39
Checking the oil level
39
After Initial 50 Hours of Operation
40
Lubricating the engine coupler
40
Changing the stern-drive oil
40
Every 50 Hours of Operation
41
Lubricate the engine coupler
41
Every 100 Hours of Operation
41
Lubricating the propeller shaft and retorqueing the nut
41
Retorqueing the gimbal ring to steering shaft connection
42
Inspecting the bellows and the clamps
42
Checking the engine alignment
42
Lubricating the unit bearing (gimbal housing)
42
Lubricating the engine coupler
42
Checking the circuit for loose or damaged connections
42
Testing the Y-CaPS unit output
42
Checking the steering system for loose, missing or damaged parts
42
Checking the remote control for loose, missing or damaged parts
42
Lubricating the shift cable and the linkages
43
Every 250 Hours of Operation
44
Touching-up the stern-drive paint and spray with corrosion guard
44
Retorqueing the rear engine mounts
45
Changing the stern-drive oil
45
Every Year
49
Retorqueing the gimbal ring to steering shaft connection
49
Inspecting the bellows and the clamps
49
Checking the engine alignment
50
Lubricating the unit bearing (gimbal housing)
50
Lubricating the engine coupler
50
Checking the circuit for loose or damaged connections
50
Testing the Y-CaPS unit output
50
Checking the steering system for loose, missing or damaged parts
50
Checking the remote control for loose, missing or damaged parts
50
Lubricating the cable and the linkages
50
Touching-up the stern-drive paint and spray with corrosion guard
50
Changing the stern-drive oil
50
Retorqueing the rear engine mounts
50
Troubleshooting
51
Long-Term Storage
53
Cold Weather (Freezing Temperature), Seasonal and Extended Storage
53
Stern-Drive Lay Up
53
Stern-Drive Recommissioning
54
Specifications
55
Need help?
Do you have a question about the Yanmar Stern-Drive ZT370 and is the answer not in the manual?
Ask a question
Yanmar Stern-Drive ZT370 Specifications
General
Brand
Yanmar
Model
Stern-Drive ZT370
Category
Outboard Motor
Language
English
Related product manuals
Yanmar ZT370
60 pages
Yanmar SD60
44 pages
Yanmar D27
142 pages
Yanmar D27-series
47 pages
Yanmar D36-series
47 pages
Need help?
General
To Next Page
