This document describes the 125LB Push Spreader, a piece of equipment designed for spreading various materials.
Function Description:
The 125LB Push Spreader is designed to evenly distribute a wide range of materials such as fertilizer, grass seed, and ice melt. It operates by being pushed at a brisk walking speed (approximately three miles per hour). The material is held in a hopper and then distributed by an impeller, with the flow rate controlled by an adjustable handle. The design emphasizes ease of use and consistent coverage for lawn care and other spreading tasks.
Important Technical Specifications:
- Load Capacity: 125lb
- Spreader Type: Broadcast
- Hopper Material: Polypropylene
- Hopper Dimensions: 29.5" x 16.5" x 13.4"
- Overall Dimensions: 43.3" x 31.5" x 33.5"
- Wheel Size: 14"
Usage Features:
- Handle: Designed for easy pushing and movement of the spreader.
- Flow Control: An adjustable lever on the handle controls the flow of material. Moving the handle to "30" fully opens the adjustable plate, while "0" fully closes it. A wing nut allows the user to lock the adjustment lever in the desired position.
- Hopper: The main container for holding spreading material, with a maximum load capacity of 125lb.
- Tires/Wheel: Designed to support the load and facilitate movement.
- Impeller: Evenly distributes the material as the spreader is pushed.
- Support Leg: Stabilizes the spreader when not in motion and supports the load.
- Screen: Included to prevent large clumps or debris from entering the impeller mechanism.
- Rain Cover: Provided to protect the material in the hopper from moisture.
- Material Compatibility: Suitable for fertilizer, grass seed, and ice melt. It is explicitly stated that materials like powders, manure, top soil, gravel, and mulch should not be used due to their unsuitable physical characteristics.
- Speed Dependency: The spread pattern and flow rate are affected by walking speed; a brisk walking speed of 3 MPH is recommended for optimal performance. Slower or faster speeds will alter the spread application rate.
- Coverage Consistency: To ensure consistent coverage, broadcast patterns should slightly overlap. The manual provides a chart for approximate broadcast widths (10' to 12' with the shield up).
- Flow Control Plate: Always close the flow control plate before turning or stopping to prevent over-application and waste.
- Starting Operation: Always begin walking before opening the closure plate.
- Tilting: Keep the impeller plate horizontal during operation to ensure even coverage.
- Windy Conditions: Do not use the spreader on windy days when spreading grass seed or herbicides, as this can lead to uneven distribution.
- Safety Warnings: Emphasizes reading and understanding the manual completely before use. Warnings include not carrying passengers, not allowing children to play on the spreader, inspecting the spreader before each use, replacing damaged parts, tightening hardware, avoiding large holes/ditches, being careful on steep grades, not pushing near creeks/ditches/highways, using caution when loading/unloading, and never towing with a motorized vehicle. Crush and cut hazards are also highlighted, advising to keep hands and feet clear of moving parts and to wear safety gear.
- Prop 65 Warning: States that the product can expose users to chemicals including lead and lead compounds, known to cause cancer and birth defects or other reproductive harm.
Maintenance Features:
- Cleaning: After each use, the hopper should be cleaned, and the spreader should be rinsed and dried both inside and out. It is important to wash between the shut-off plate and the bottom of the hopper.
- Tire Pressure: Before operating, ensure tires have the recommended pressure.
- Fastener Checks: Periodically check all fasteners for tightness.
- Lubrication: Annually clean and lightly lubricate parts.
- Paint Touch-Up: Use glossy enamel spray paint to touch up scratched or worn painted metal surfaces.
- Load Capacity Adherence: Never exceed the 125lb load capacity, as this will damage the spreader.
- Part Replacement: If parts need replacement, only use manufacturer-specified parts to avoid safety hazards or poor operation.
- Storage Preparation: Before storing, ensure the spreader is clean and dry.
- Material Removal: Never allow material to remain in the hopper for extended periods.
- Storage Location: Store indoors or in a protected area during severe weather and winter months.
- Salt Usage: Explicitly states "DO NOT USE SALT." Using salt will damage the mechanism and shorten the life of the machine.
The manual also includes detailed assembly instructions with diagrams, a table of contents, hazard signal word definitions, and a parts drawing with a corresponding parts list. A limited warranty section outlines coverage for one year from the purchase date, excluding cosmetic defects, normal wear, misuse, neglect, accidents, abuse, overloading, modification, or incorrect assembly.
Need help?
General
To Next Page
