YASKAWA Varispeed-616G3

APPENDIX E
OPTIONS
(1) OPTION CARDS
(Except digital output card
DO-08, there treininals are
to be connected only class 2 circuits .
Notes

1 . Only one option card can be installed at 2CN at a time
2 Only one option card can be installed at 3CN at a time
3

When a communication interface card is attached at 2CN, no option card can be attached at 3CN .
4 All option card terminals (except digital output card DO-08) should be connected to class 2 circuits .
OPTIONS
Name
Code No . Function Installing Position Document No .
Analog
I Permits setting a
high-accuracy,
high-resolution analog speed refer-
Attach the card
at
Speed
73600-000IX
ence
" Input signal level : 0 to
+ IOVDC
(20k12) 1 channel
2CN
on the control ' TOE-
Reference Card
4 to 20mA DC (25052) 1 channel
circuit
board . ~ C736-30 .13
AI-14U
" Input signal level : 14 bits (1/16384)
(See Note 1)
Analog
Permits setting a high-accuracy, high-resolution analog speed refer-
Attach the card at
'
Speed
73600-0002X
ence
" Input signal level : 0 to ± IOVDC (20W),
2CN on the control TOE-
Reference Card
4 to 20mA DC (25012 ; 3 channels
circuit board . C736-30 .14
AI-14B
" Input re so lution : 13 bits + sign (1/8192)
(See Note 1)
Digital Speed
Permits setting an 8-bit digital speed reference
Attach the card at
o .
Reference
"
Input signal : Binary 16 bits/BCD 2 digits
+
Sign
2CN
on the control TOE-
CardCard
73600-0003X " Input voltage : +24V (isolated)
circuit board
. C736-30 .15
DI-08
"
Input current
:
8mA
(See Note 1)
Digital Speed
Permits setting
16-bit digital speed reference .
Attach the card at
Reference
" Input signal : Binary
16
bits/BCD 4 digits + sign
2CN on the control
TOE-
Card
73600-CO I IX "
Input
voltage :
+24V
(isolated)
Supplied by external device .
circuit board .
C736-30 .17
DI-16G
"
Input current : 8mA/point
I
(See Note 1)
Permits operation or constant setting by command from master
Attach the card at
Communication
controller .
2CN on the control '
Interface Card
73600-CO06X " Communicationmethod : Synchronous -
circuit board .
SI-B " Communication speed : 19 .2kBPS (up to 136 .5kBPS possible)
" In t erface : RS-232, RS-422, RS-485
(See Note 1) ,
Analog
Provides an
analog
signal for monitoring
the output state (output fre-
Attach the card at
quency, output
current,
etc .)
of
the inverter .
3CN on the control TOE-
CardCard
73600-DOOIX "
Output resolution : 8 bits (1/256)
circuit board . C736-30 .21
AO-08
"
Output voltage : 0 to
+
1OV (not isolated)
(See Note 2)
"
Output channel : 2 channels
Analog
Provides an analog signal for monitoring the output state (output fre-
Attach the card
at
Monitor
quency, output current etc .) of the inverter .
3CN on the control
TOE-
Card
Card
" Output resolution :
11
bits (1/2048)
circuit board .
C736-30 .22
"
Output voltage : 0 to
+
lOV (not isolated)
° AO-12
" Outut channel : 2 channels
(See Note 2)
Pulse
Provides a pulse string signal corresponding to the output frequency
Attach the card at
of the inverter .
Monitor
73600-DO03X
" Output pulse : IF, 6F, IOF, 12F, 36F (F : Output frequency)
3CN on the control TOE-
Card
"
Output voltage :
+
12V ± l0~% 0 (isolated)
circuit board . C736-30 .23
PO-36F
"
O utput current : 20 mA m ax .
(See Note 2)
Digital
Extends multifunction output signal output status .
Attach the card at
Output method
:
Open
collector output x 6 points
Output
73600-DO04X
(48 VDC 50mA or less)
3CN on the control TOE-
Card
:
Relay contact (la) 250VAC IA or less
circuit board . C736-30 .24
DO-08
output
x
2 points 30VDC IA or less
(See Note 2)
for more: efesotomasyon - Yaskawa drive