YOKOGAWA FLXA202

To Next Page

To Previous Page

IM 12A01A02-01E 8th Edition : Oct. 01, 2015-00

n Mark position of intrinsic safety

The mark position of intrinsic safety is shown as follows

FLXA202-D-*-…

Type:-CB

*1: This marking conforms to Intrinsic safety of IECEx.

*2: This marking conforms to Intrinsic safety of ATEX.

Main Page

Default Chapter6
- Bottom Side6
- Table of Contents11
Introduction17
- Section 3 Section17
- Instrument Check19
- Screen Operation21
  - Section 4 Section21
  - Section 5 Section22
- Maintenance25
- Passwords26
- Regulatory Compliance26
1 Introduction and General Description17
2 Wiring and Installation36
- Section 11 Section37
- Installation Site38
- Removing the Wiring Cover39
- Installing the Cable Glands40
- Wiring the Power Supply42
- Sensor Wiring46
- Mounting Methods55
- Operation56
3 OPERATION of Ph/Orp57
- Change Language58
- Quick Setup58
- Home Display, Main Display and Monitor Display60
- Zooming in on Details61
- Trend Graphics66
- Instrument Status Screen67
- Calibration and Commissioning68
4 COMMISSIONING of Ph/Orp69
- Sensor Setup71
- Measurement Setup71
- Output Setup77
- Error Configuration79
- Logbook Configuration81
- Advanced Setup81
- Display Setup85
- Calculated Data Setup88
5 CALIBRATION of Ph/Orp89
- Ph Calibration90
- Temperature Calibration93
- ORP Calibration (Rh Calibration)93
- Hold94
- Temporary Output94
6 OPERATION of SC (Conductivity)95
- Change Language95
- Quick Setup96
- Home Display, Main Display and Monitor Display98
- Zooming in on Details100
- Trend Graphics104
- Instrument Status Screen105
- Calibration and Commissioning106
7 COMMISSIONING of SC (Conductivity)107
- Measurement Setup109
- Calibration Settings111
- Error Configuration115
- Logbook Configuration116
- Advanced Setup117
- Passwords118
- Factory Setup119
- Trend120
- Auto Return121
8 CALIBRATION of SC (Conductivity)123
- Cell Constant (Manual)123
- Air Calibration124
- Cell Constant (Automatic)124
- Cell Constant (Manual)124
- Hold124
- Sample124
- Hold125
- Temperature Calibration125
- Temperature Coefficient125
- Temporary Output126
9 OPERATION of ISC (Induvtive Conductivity)127
- Change Language128
- Quick Setup128
- Main Display and Monitor Display130
- Zooming in on Details131
- Trend Graphics135
- Instrument Status Screen137
- Calibration and Commissioning137
10 COMMISSIONING of ISC (Inductive Conductivity)138
- Measurement Setup138
- Output Setup143
- Error Configuration144
- Logbook Configuration145
- Advanced Setup146
- Display Setup148
11 CALIBRATION of ISC (Inductive Conductivity)150
- Cell Constant151
- Air Calibration152
- Cell Constant (Automatic)152
- Cell Constant (Manual)152
- Sample153
- Temperature Coefficient153
- Hold154
- Temperature Calibration154
12 OPERATION of DO (Dissolved Oxygen)155
- Change Language156
- Quick Setup156
- Home Display, Main Display and Monitor Display158
- Zooming in on Details159
- Trend Graphics163
- Instrument Status Screen164
- Calibration and Commissioning164
13 COMMISSIONING of DO (Dissolved Oxygen)166
- Sensor Setup167
- Measurement Setup168
- Output Setup170
- Error Configuration172
- Logbook Configuration173
- Advanced Setup174
- Display Setup177
- Calculated Data Setup179
14 CALIBRATION of DO (Dissolved Oxygen)180
- Air Calibration181
- Water Calibration181
- Manual Slope Calibration182
- Temperature Calibration182
- Hold183
- Temporary Output183
15 OPERATION of SENCOM Ph/Orp184
- Change Language185
- Quick Setup185
- Main Display and Monitor Display187
- Zooming in on Details188
- Trend Graphics195
- Instrument Status Screen196
- Calibration and Commissioning196
16 COMMISSIONING of SENCOM Ph/Orp198
- Sensor Setup200
- Measurement Setup201
- Output Setup207
- Error Configuration208
- Logbook Configuration209
- Advanced Setup210
- Display Setup214
17 CALIBRATION of SENCOM Ph/Orp216
- Ph Calibration217
- Temperature Calibration220
- ORP Calibration (Rh Calibration)220
- Hold221
18 Maintenance222
- Periodic Maintenance222
19 Troubleshooting223
Appendix 1 for Ph/Orp226
Appendix 2 for SC (Conductivity)230
Appendix 3 for ISC (Inductive Conductivity)242
- Measurement Principle251
Appendix 4 for DO (Dissolved Oxygen)253
Revision Record257

YOKOGAWA FLXA202

Table of Contents

Other manuals for YOKOGAWA FLXA202

Related product manuals