York DNZ 060 User Manual

ISO 9001
Certified Quality
Management System
CONTENTS
INSTALLATION SAFETY INFORMATION. . . . . . . . .3
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
MAINTENANCE AND RENEWAL PARTS. . . . . . . . .3
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . .4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . .15
START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . .19
See following pages for a complete Table of Contents.
NOTES, CAUTIONS AND WARNINGS
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes
are intended to
clarify or make the installation easier. Cautions
are given to
prevent equipment damage. Warnings
are given to alert
installer that personal injury and/or equipment damage may
result if installation procedure is not handled properly.
INSTALLATION
MANUAL
CAUTION: READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.
SAVE THIS MANUAL
CHAMPION
®
R-410A
SINGLE PACKAGE GAS/ELECTRIC
AIR-COOLED AIR CONDITIONERS
2, 2-1/2, 3, 3-1/2, 4 and 5 NOMINAL TON
WITH R-410A REFRIGERANT
MODELS: DNZ 024, 030, 036, 042, 048, and 060
66433-YIM-B-1004

York DNZ 060 Specifications

General

Brand	York
Model	DNZ 060
Category	Air Conditioner
Language	English

Summary

Installation Safety Information

General Unit Description

General information about YORK Model DNZ units, designed for outdoor installation.

Unit Inspection Procedures

Procedures for inspecting the unit for possible damage during transit upon receipt.

Approvals and Certifications

Details CSA certification for unit installation and use as a forced air furnace.

Unit Nomenclature

Installation Limitations and Codes

Lists national and local safety codes that must be followed for unit installation.

Unit Location Guidelines

Rigging and Handling Instructions

Safe procedures for moving and lifting the unit, including spreader bar use.

Required Clearances

Specifies minimum clearances needed for proper unit operation and servicing.

Duct Work Installation

Filter Requirements

Details filter requirements and maintenance for unit air intake for optimal performance.

Service Access Points

Identifies locations of access panels for serviceable components and system checks.

Thermostat Installation

Recommends thermostat location and general installation guidelines for proper function.

Power and Control Wiring

Control Wiring Diagram

Illustrates field wiring for thermostat and unit control circuit connections.

Power Wiring Diagram

Shows typical field wiring for unit power supply connections and disconnects.

Compressor Information

Compressor Phasing

Guidance on checking and correcting three-phase compressor rotation for proper operation.

Gas Piping Requirements

Gas Connection Procedure

Details routing and connection of the gas supply line to the unit.

Flue Vent Hood Installation

Flue Vent Hood Fastening

Instructions for fastening the flue vent hood to ensure proper unit operation.

Unit Dimensions

Minimum Clearances Table

Table specifying minimum clearances required for unit operation and servicing.

Sequence of Operation

Heating Sequence

Detailed operational sequence for the heating mode, including safety controls.

Heating Safety Controls

Explanation of safety controls used during the heating operation cycle.

Cooling Sequence

Detailed operational sequence for the cooling mode, including safety controls.

Cooling Safety Controls

Explanation of safety controls used during the cooling operation cycle.

Unit Start-Up Procedures

Pre-Start Check List

Essential checks to complete before initiating unit start-up.

Operating Instructions

Step-by-step instructions for operating the unit safely and correctly.

Manifold Gas Pressure Adjustment

Guidance on adjusting gas pressure for optimal burner performance.

Burner Instructions

Hot Surface Pilot Instructions

Detailed instructions for adjusting and servicing the hot surface pilot assembly.

Temperature Rise Adjustment

Checking Gas Input

Procedures for verifying the unit's gas input rate for proper operation.

Troubleshooting Guide

Wiring Diagram Notes

R-410A Quick Reference Guide

Essential information and precautions for servicing R-410A refrigerant systems.