Zephyr Pisa ZPI-E30BG

Questions and Answers

K
Kristin GrossAug 16, 2025
What to do if my Zephyr Pisa ZPI-E30BG Ventilation Hood doesn’t work after installation?
- J
  Jordan RobinsonAug 16, 2025
  If your Zephyr Ventilation Hood doesn’t work after installation, first ensure that the circuit breaker and the unit’s power are turned ON. Check that the power line and cable locking connector are properly connected. Also, make sure the wirings at the switch board and control board are connected properly. If the issue persists, the switch board or control board might be defective and need to be changed. Finally, check the wires on the control board and ensure they are connected properly.
L
Lynn WilliamsAug 19, 2025
How to fix a Zephyr Pisa ZPI-E30BG Ventilation Hood that doesn't work after installation?
- M
  Michael PhillipsAug 19, 2025
  If your Zephyr Ventilation Hood isn't working after installation, start by ensuring that the power source is turned on, checking both the circuit breaker and the unit's power switch. Verify that the power line and cable locking connector are properly connected. Inspect the switch board and control board wirings to confirm they are securely connected. If issues persist, the switch board or control board might be defective and need replacement. Also, make sure the wires on the control board are connected properly.
T
Troy ChaseAug 22, 2025
What to do if the light works but the blower is not turning on my Zephyr Pisa ZPI-E30BG Ventilation Hood?
- M
  Marcus VaughnAug 22, 2025
  If the light on your Zephyr Ventilation Hood is working but the blower isn't turning, there are several potential causes. First, ensure the blower wire is properly plugged into the molex connector. If the blower has overheated, the thermally protected system may have shut it down; allow it to cool down. A damaged capacitor could also be the issue, requiring replacement. Finally, the blower itself might be defective and need to be replaced.
J
Jake MitchellAug 25, 2025
What to do if the blower is working but the LumiLight LEDs are not on my Zephyr Pisa ZPI-E30BG Ventilation Hood?
- M
  Matthew RodriguezAug 25, 2025
  If the blower in your Zephyr Ventilation Hood is working, but the LumiLight LEDs are not, there are a few possible reasons. First, check if the LumiLight LED connector is disconnected and connect it. If that's not the issue, the LumiLight LED might be defective and need replacement. In some cases, a defective switch board or control board can also cause this problem, requiring their replacement.
D
David HoAug 27, 2025
Why is my Zephyr Ventilation Hood not venting out properly?
- M
  mariahstrongAug 28, 2025
  If your Zephyr Ventilation Hood isn't venting properly, several factors could be the cause. First, ensure you're using the correct size of ducting; if not, replace it with the appropriate size. The hood's height above the cooktop is also crucial; adjust it to be within 20-32 inches, depending on whether you have an electric or gas cooktop. External wind from open windows or doors can disrupt ventilation, so close them to eliminate airflow. Lastly, check for any blockages in the duct opening or ductwork and remove them.
P
Peggy WilliamsAug 30, 2025
Why is my Zephyr Ventilation Hood vibrating?
- B
  Bradley MartinAug 30, 2025
  If your Zephyr Ventilation Hood is vibrating, it could be due to a few reasons. Check that the blower is securely in place and tighten it if necessary. A damaged blower wheel can also cause vibration, so consider replacing the blower. Lastly, ensure that the hood itself is properly secured in place by checking its installation.
N
Natasha CampbellSep 3, 2025
Why is my Zephyr Pisa ZPI-E30BG whistling?
- A
  arthur72Sep 3, 2025
  If your Zephyr Ventilation Hood is whistling, it's likely due to either a filter not being in the correct position or duct pipe connections that aren't properly sealed. Try adjusting the filters until the whistling stops. Also, inspect the duct pipe connections to ensure they are all sealed correctly.
T
Tammy DavisSep 5, 2025
Why is the filter vibrating in my Zephyr Ventilation Hood?
- S
  Scott WongSep 6, 2025
  If the filter in your Zephyr Ventilation Hood is vibrating, it could be due to the filter being loose. Try adjusting or changing the filter. Alternatively, the spring clip on the filter might be broken, in which case you should replace the spring clip.
R
Rachel FieldsSep 9, 2025
What to do if the blower is working, but the LumiLight LEDs are not on my Zephyr Pisa ZPI-E30BG?
- G
  gabrielletrevinoSep 9, 2025
  If the blower is working but the LumiLight LEDs are not on your Zephyr Ventilation Hood, first check if the LumiLight LED connector is disconnected and connect it. If that's not the issue, the LumiLight LED might be defective and need to be changed. Alternatively, the switch board or control board could be defective, requiring replacement.
A
April WaltonSep 12, 2025
Why do LumiLight LEDs flicker when changing speed levels on my Zephyr Pisa ZPI-E30BG?
- Z
  Zachary GreenSep 12, 2025
  This is a normal operation and the hood is working correctly.

Summary

Safety Information

General Safety and Warning Symbols

General safety precautions and explanation of warning symbols.

Specific Safety Warnings

Detailed warnings related to fire, shock, and grease fires.

Operation and Electrical Requirements

Installation Instructions

Ducting Calculation Sheet

Mounting Height, Clearance, & Ducting

Specifies installation height and ducting requirements.

Ducting Options

Hood Specifications

Electrical Supply and Cable Lock

Preparing the Cabinet

Horizontal Ducting Conversion

Mounting the Hood

Final steps for mounting, ducting, and filler panel.

Recirculating Kit Installation

Ductless Recirculation

Features & Controls

Slide Controls

Maintenance

Hood & Filter Cleaning

Wiring Diagram

ZPI-E24 BS Wiring Diagram

Electrical schematic for the ZPI-E24BS model.

ZPI-E30 BS & ZPI-E36 BS Wiring Diagram

Electrical schematic for ZPI-E30BS and ZPI-E36BS models.

Troubleshooting

Unit Operation and Light Issues

Common problems and solutions for unit operation and lights.

Venting and Filter Issues

Solutions for venting problems and filter vibration.

List of Parts & Accessories

Limited Warranty

Obtaining Service and Warranty Exclusions

Zephyr Pisa ZPI-E30BG Specifications

General

Color	stainless steel
Hood Type	under cabinet
Venting Type	convertible
Temperature Sensor	no
Number of Fan Speeds	3
CFM	500 cubic feet per minute
Filters	2
Sones	5.3 sones
Control Type	slide
Delay Start	no
Interior Light	yes
Remote Control	no
Voltage	120 volts