ZETRON 4018 - Installation Manual

418 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Series 4000

Communication Control System

Installation and Configuration

025-9533Y

Table of Contents

Default Chapter7
- Table of Contents7
Introduction15
- Overview15
- System Overview17
  - Identification of Console Models20
- Installation Sequence22
- Manuals24
- Specifications25
Common Control Equipment Installation29
- Model 4048 Mounting30
  - Power Supply30
  - CCE Console Cardcage30
  - CCE Channel Cardcage31
- Model 4048 CCE Set up31
  - Model 4048 Slot and Card Identification31
  - Model 4048 Power Supply32
  - Console Cardcage36
  - Channel Cardcage37
- Model 4020 CCE Set up37
  - Model 4020 Slot and Card Identification37
  - Power Supplies for Model 4020 Systems37
- System Grounding39
- Configuring the System Traffic Card (STC)41
  - STC Switches41
  - Jumpers42
- Configuring Console Cards42
  - CIC Switches42
  - CIC Jumpers44
- Configuring the Patch Card44
  - Patch Card Switches44
  - Patch Card Jumpers45
- Connector Identification45
- Configuring Channel Cards48
  - Line Termination49
  - Channel Cross-Mute50
  - Call Source50
  - Busy Transmit Inhibit51
  - Duplex51
  - High Level Guard Tone Duration52
  - Guard Tone Frequency52
  - Low Level Guard Tone Amplitude53
  - LOTL Disable53
  - Channel VOX Hang Time53
  - Dual Channel Recorder Output Audio53
  - Tone/Local Software Configuration54
  - Channel Configuration56
  - Enhanced Call Detection Mode62
  - LED Error Display65
- Wiring to the Channels65
  - Push-To-Talk71
  - Carrier Operated Relay71
  - Auxiliary Output71
  - Transmit Audio71
  - Receive Audio71
  - Cross-Busy Input/Output72
  - Base Station Installation72
- Auxiliary I/O Card Installation (Optional)72
  - Overview72
  - Electrical Specifications73
  - Configuring the Auxiliary Input/Output Card74
  - Wiring to the Auxiliary Input/Output Card77
  - Relay Output Connections80
  - Auxiliary Relay Output Jumper Setting81
  - Input and Timing Input Connections83
  - Standard Input Connections85
  - Isolated Input Connections85
- Wiring to the Consoles86
  - Wire Distribution87
  - Console Signal Descriptions89
- Series 4000 Phone Coupler (Optional)91
  - Specifications91
  - Installation92
  - Testing94
- Wiring to the Logging Recorder100
- Wiring to the Service Ports102
- Wiring to the Alarm Circuit103
- Modem Configuration104
- Modem and Service Port Operation105
  - Modem and Computer Setup105
  - Operation105
- Logger Port Function109
- ANI Signaling109
Wireless Interface Options111
- MAP27 Wireless Interface Option111
- Harris M7100 Wireless Interface Option132
- Harris M7300 Wireless Interface Option144
- (P/N 950-1113)147
Console Installation155
- Introduction155
- Physical Placement, Desktop156
  - Labelling156
  - Console Access156
- Physical Placement, Rackmount157
- Power157
- Programming Desktop and Rackmount Consoles159
- Configuring a Console160
- Configuring Model 4115B Console Expander164
- Wiring the Dispatch Consoles164
System Check173
- Bringing the System Online173
- On-Card Diagnostics174
Audio Level Adjustments177
- Overview177
- Dual Channel Card Audio Levels181
- Microphone Adjustments185
- Console Line Loss Compensation186
- Transmit Monitor Adjustment186
- Auxiliary Audio Input Adjustment187
- Other Audio Adjustments187
  - Setting Rx Levels for Dual Channel Cards190
- (VOX Input Connected to AGC Input)190
Console Programming System193
- Introduction193
- Versions and Compatibility193
  - DOS and Windows193
  - Firmware Compatibility194
- Installation194
  - Uninstallation194
- CPSW Menu Structure195
- Using CPSW197
Accessory Installation219
- Zetron Desktop Microphone220
- Gooseneck Microphone221
- Headset Jackbox221
- Footswitch221
- Telephone Radio Headset Interface222
- Secondary Headset Jackbox223
  - Installation224
  - Console Programming225
- Zetron Desktop Speakers (Monitor A/B)226
- T2-2R Base Station Installation228
  - Single System Channel228
  - Dual System Channels228
- Spectracom NETCLOCK Set up229
Console ANI Programming231
- Signaling231
- Modes231
- Programming232
- 5/6 Tone ANI Decoding232
  - Selection of Tone Set232
- MDC-1200 ANI Decoding233
- GE-Star ANI Decoding233
  - Output Format234
  - Error Indications235
Integratorrd Workstation Installation237
- Overview237
  - Feature Summary (with Model 4020/4048 Common Controller)237
- Hardware Installation238
- Operator Position Installation245
  - Overview245
  - PC Configuration246
- Preparing the Console Computer248
  - PC Configuration248
- Software Installation251
Integratorrdps Programming259
- Introduction260
  - General Description260
  - Integratorrd Concepts and Definitions260
- Getting Started261
- Creating a Console Configuration266
- Defining Radio Channels267
- System-Specific Definitions276
- Specifying the Keyboard and Expansion Panel Layout327
- Button Assignments330
  - Entering Display Setup Button Labels332
  - Entering Select, Xmit, and Group Patch Button Labels332
- Copying Console Configuration Data333
- Saving a Configuration334
Radio System Management Program335
- Installing RSMP335
- Uninstalling RSMP337
- RSMP Operation337
- Reports346
  - 24-Hour Reports346
  - Raw Data Files348
Installation Verification351
- Overview351
- Procedure351
Appendix A: Radio System Management Interface353
- Message Format354
- Message Content: Messages from Channels355
- Message Content: Messages from Consoles357
Appendix B: Troubleshooting359
Appendix C: CPSW Reference Material363
- DC and Tone Remote Function Definitions364
- Achieving Motorola/Ge DC Control Currents365
- Paging Format Specifications366
- Description of Key Functions and Parameters372
Appendix D: Power Supply Worksheet389
Appendix E: List of Audio Delays391
Appendix F: Integratorrd Buttons393
- Standard Functions394
- Wireless Functions402
- Menu Options408
  - Placement408
Index411

Other manuals for ZETRON 4018

Manual160 pages

Related product manuals

Preview: ZETRON 4000 Series

ZETRON 4000 Series

ZETRON 4000 Sereis